BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

More documents

Recommendations

Info

11.4.1. Performance TestAlso known as a capacity test, the performance test uses a programmed constant currentor constant power load to project reliability <strong>and</strong> remaining battery life before replacementis necessary. A performance test has only one step.Figure 7. Setup - Test Setup: Performance20
11.4.2. Modified Performance TestA modified performance test tests battery capacity (similar to a performance test) <strong>and</strong> theability of the battery to provide a high-rate, short-duration load cycle. This test may bedone in place of a service test. If you type 0 (zero) for Rated Time, the test does notcalculate battery capacity.Figure 8. Setup - Test Setup: Modified Performance11.4.3. Service TestA service test determines the battery “as found” ability to satisfy the battery duty cycle.Figure 9. Setup - Test Setup: Service21
Page 5 and 6: 1. Warranty and Limitation of Liabi
Page 9 and 10: Table of Contents1. WHAT'S NEW ....
Page 11: 15.8. Preamp Offset and Gain As-Fou
Page 14 and 15: The manual has more screen shots. I
Page 16 and 17: 3. System RequirementsThe following
Page 18 and 19: 5. PasswordWhen you select certain
Page 20 and 21: 7. BCT-2000 Initial TestBefore conn
Page 22 and 23: 8. Main MenuThe main menu is where
Page 24 and 25: 9. Recommended TestsPrior to perfor
Page 26 and 27: 10. Connecting the SystemAfter perf
Page 28 and 29: 17. Connect the leads labeled IT-1(
Page 30 and 31: Add Site / Delete Site - To add a s
Page 34 and 35: 11.4.4. Rundown TestA rundown test
Page 36 and 37: 11.5.3. Temperature and CorrectionA
Page 38 and 39: 11.5.7. Calculate Capacity at Targe
Page 40 and 41: 11.7. Load BankOn the Setup menu, c
Page 42 and 43: 11.8. ContactOn the Setup menu, cli
Page 44 and 45: Test Leads and Voltages - Click a b
Page 46 and 47: 20, 10, 5, 1 and All Off - You may
Page 48 and 49: 12.5. Test Screen ToolbarThe Toolba
Page 50 and 51: Figure 26. Test Steps - Constant Po
Page 52 and 53: 12.6. Charger Test ScreenWhen the C
Page 54 and 55: The Files of Type drop-down list le
Page 56 and 57: 13.5. Criteria ScreenClick the Crit
Page 58 and 59: Ignore Zero Target Steps in Capacit
Page 60 and 61: 13.9. Filter ScreenClick the Filter
Page 62 and 63: Change - Use the Properties dialog
Page 64 and 65: 13.17. Opening an Archive FileLoad
Page 66 and 67: 14. Running DiagnosticsThe DAM (Dat
Page 68 and 69: 14.3. Load Bank DiagnosticLoad bank
Page 70 and 71: Figure 50. Load Bank AnalysisThe Lo
Page 72 and 73: 15. System CalibrationThis section
Page 74 and 75: 15.4. Cell As-Found1. Complete the
Page 76 and 77: 15.8. Preamp Offset and Gain As-Fou
Page 78 and 79: 15.10. Cell Calibration1. Calibrate
Page 80 and 81: 15.12. Overall Battery Calibration1
Page 82 and 83:
15.14. Print a Calibration ReportAf
Page 84 and 85:
17. Upgrading BCT-2000 SoftwareUpgr
Page 86 and 87:
3. Select F2 Load Control Diagnosti
Page 88 and 89:
OVERALLBATTERYBefore CalibrationAft
Page 90 and 91:
19. Run Time Error MessagesRun Time
Page 92 and 93:
21. Appendix A: BCT-128 Parts ListQ
Page 94 and 95:
23. Appendix C: Spare PartsBCT-2000
Page 96 and 97:
constant power button .............
Page 98:
Ssafety information ...............
show all

BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?