BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

More documents

Recommendations

Info

7. BCT-2000 Initial TestBefore connecting equipment for an actual test, check all the BCT components for functionaloperation.First, test the laptop computer. Remove the computer from its shipping case and connect thepower cable. (Refer to the laptop computer manual.) Power up the computer and verify the screendisplays the Windows desktop and the BCT-2000 icon. If it does not, contact Albércorp fortechnical assistance. Power off the computer to end the test.7.1. Initial System TestRefer to drawing BCT-2436-D1110 System Block Diagram for connection of the cables fromthe computer to the BCT-128 or BCT-256 data logging acquisition device. The system has aserial interface, which uses a 9-pin to 9-pin cable. The following steps describe theconnections for proper operation:1. Before making any connections, ensure all equipment is powered off.2. Connect one end of the 9-pin to 9-pin cable to the serial port of the laptop computer.3. Connect the other end of the cable to the BCT computer port.4. Connect the AC power cable to the BCT-128 or BCT-256, and plug the other end into a120VAC 60Hz receptacle.5. Unpack the printer. Plug the AC adapter into the small power receptacle on the printer,and the other end into a 120VAC 60Hz receptacle.6. Connect the male end of the six foot printer cable to the printer cable port near the ACadapter input. Connect the other end to the computer 25-pin D-Sub female connector onthe rear of the unit.7. Load paper into the printer. NOTE: The printer is not required during an actual load test.8. Unpack the CS-2000 if available. Locate the two test cables and one power cable for theunit. The parallel cables each have a female and male D-Sub, 37-pin connector.9. Connect the power cable to the CS-2000 and to a 120VAC 60Hz receptacle.10. Connect one 37-pin cable between the CS-2000 Cell Outputs rear connector and the BCTCells 1-32 connector.11. Connect the other 37-pin cable between the CS-2000 System connector and the Systemconnector on the BCT.12. Power on the four devices: The BCT-128 or 256, the laptop computer, the printer, and theCS-2000.13. Verify the Windows desktop appears.14. Click the BCT2000 icon to start the program.15. On the main menu, select DAM. Verify the BCT relays are clicking.16. On the DAM dialog box, at Display Board, select 1.8
17. On the DAM dialog box, observe A/D counts of at least 10000 if no CS-2000 isconnected. Varying the CS-2000 causes the A/D counts to vary.18. Close the DAM dialog box and exit the BCT program.19. To test the printer, open a word processing program, select the printer driver, then sendoutput to the printer.20. After verifying operation, power off the equipment and disconnect the cables. Place allthe cables and components back into the shipping cases as found when unpacking.9
Page 5 and 6: 1. Warranty and Limitation of Liabi
Page 9 and 10: Table of Contents1. WHAT'S NEW ....
Page 11: 15.8. Preamp Offset and Gain As-Fou
Page 14 and 15: The manual has more screen shots. I
Page 16 and 17: 3. System RequirementsThe following
Page 18 and 19: 5. PasswordWhen you select certain
Page 22 and 23: 8. Main MenuThe main menu is where
Page 24 and 25: 9. Recommended TestsPrior to perfor
Page 26 and 27: 10. Connecting the SystemAfter perf
Page 28 and 29: 17. Connect the leads labeled IT-1(
Page 30 and 31: Add Site / Delete Site - To add a s
Page 32 and 33: 11.4.1. Performance TestAlso known
Page 34 and 35: 11.4.4. Rundown TestA rundown test
Page 36 and 37: 11.5.3. Temperature and CorrectionA
Page 38 and 39: 11.5.7. Calculate Capacity at Targe
Page 40 and 41: 11.7. Load BankOn the Setup menu, c
Page 42 and 43: 11.8. ContactOn the Setup menu, cli
Page 44 and 45: Test Leads and Voltages - Click a b
Page 46 and 47: 20, 10, 5, 1 and All Off - You may
Page 48 and 49: 12.5. Test Screen ToolbarThe Toolba
Page 50 and 51: Figure 26. Test Steps - Constant Po
Page 52 and 53: 12.6. Charger Test ScreenWhen the C
Page 54 and 55: The Files of Type drop-down list le
Page 56 and 57: 13.5. Criteria ScreenClick the Crit
Page 58 and 59: Ignore Zero Target Steps in Capacit
Page 60 and 61: 13.9. Filter ScreenClick the Filter
Page 62 and 63: Change - Use the Properties dialog
Page 64 and 65: 13.17. Opening an Archive FileLoad
Page 66 and 67: 14. Running DiagnosticsThe DAM (Dat
Page 68 and 69: 14.3. Load Bank DiagnosticLoad bank
Page 70 and 71:
Figure 50. Load Bank AnalysisThe Lo
Page 72 and 73:
15. System CalibrationThis section
Page 74 and 75:
15.4. Cell As-Found1. Complete the
Page 76 and 77:
15.8. Preamp Offset and Gain As-Fou
Page 78 and 79:
15.10. Cell Calibration1. Calibrate
Page 80 and 81:
15.12. Overall Battery Calibration1
Page 82 and 83:
15.14. Print a Calibration ReportAf
Page 84 and 85:
17. Upgrading BCT-2000 SoftwareUpgr
Page 86 and 87:
3. Select F2 Load Control Diagnosti
Page 88 and 89:
OVERALLBATTERYBefore CalibrationAft
Page 90 and 91:
19. Run Time Error MessagesRun Time
Page 92 and 93:
21. Appendix A: BCT-128 Parts ListQ
Page 94 and 95:
23. Appendix C: Spare PartsBCT-2000
Page 96 and 97:
constant power button .............
Page 98:
Ssafety information ...............
show all

BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

Create successful ePaper yourself

Delete template?

Save as template?