BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

More documents

Recommendations

Info

5. PasswordWhen you select certain functions, a password dialog box appears. The default password from thefactory is: alberFigure 1. PasswordType the password in the Enter Password box and click OK. To change the password, clickChange and follow screen instructions. Some screens that require a password may be viewedwithout a password but not modified. To view a screen, click Cancel or press ESC.If the password is changed without authorization or lost, contact Albércorp to obtain a code tounlock the system. Type this code in the Enter Factory Backup Code box and click OK. This putsthe password back to the default password alber. Change the password as previously described.6
6. Communication SettingsIf the computer does not communicate with the equipment, you may need to select a new COMport. To display the Communication Settings screen, click Communications on the main menu.Figure 2. Communication SettingsClick a button for the COM port setting, then click OK. If the required COM port is not known,you may have to try all four selections to determine which setting establishes communicationbetween the computer and the equipment.The BCT program communicates with the unit only when in the Test, Diagnostics, andCalibration screens.7
Page 5 and 6: 1. Warranty and Limitation of Liabi
Page 9 and 10: Table of Contents1. WHAT'S NEW ....
Page 11: 15.8. Preamp Offset and Gain As-Fou
Page 14 and 15: The manual has more screen shots. I
Page 16 and 17: 3. System RequirementsThe following
Page 20 and 21: 7. BCT-2000 Initial TestBefore conn
Page 22 and 23: 8. Main MenuThe main menu is where
Page 24 and 25: 9. Recommended TestsPrior to perfor
Page 26 and 27: 10. Connecting the SystemAfter perf
Page 28 and 29: 17. Connect the leads labeled IT-1(
Page 30 and 31: Add Site / Delete Site - To add a s
Page 32 and 33: 11.4.1. Performance TestAlso known
Page 34 and 35: 11.4.4. Rundown TestA rundown test
Page 36 and 37: 11.5.3. Temperature and CorrectionA
Page 38 and 39: 11.5.7. Calculate Capacity at Targe
Page 40 and 41: 11.7. Load BankOn the Setup menu, c
Page 42 and 43: 11.8. ContactOn the Setup menu, cli
Page 44 and 45: Test Leads and Voltages - Click a b
Page 46 and 47: 20, 10, 5, 1 and All Off - You may
Page 48 and 49: 12.5. Test Screen ToolbarThe Toolba
Page 50 and 51: Figure 26. Test Steps - Constant Po
Page 52 and 53: 12.6. Charger Test ScreenWhen the C
Page 54 and 55: The Files of Type drop-down list le
Page 56 and 57: 13.5. Criteria ScreenClick the Crit
Page 58 and 59: Ignore Zero Target Steps in Capacit
Page 60 and 61: 13.9. Filter ScreenClick the Filter
Page 62 and 63: Change - Use the Properties dialog
Page 64 and 65: 13.17. Opening an Archive FileLoad
Page 66 and 67: 14. Running DiagnosticsThe DAM (Dat
Page 68 and 69:
14.3. Load Bank DiagnosticLoad bank
Page 70 and 71:
Figure 50. Load Bank AnalysisThe Lo
Page 72 and 73:
15. System CalibrationThis section
Page 74 and 75:
15.4. Cell As-Found1. Complete the
Page 76 and 77:
15.8. Preamp Offset and Gain As-Fou
Page 78 and 79:
15.10. Cell Calibration1. Calibrate
Page 80 and 81:
15.12. Overall Battery Calibration1
Page 82 and 83:
15.14. Print a Calibration ReportAf
Page 84 and 85:
17. Upgrading BCT-2000 SoftwareUpgr
Page 86 and 87:
3. Select F2 Load Control Diagnosti
Page 88 and 89:
OVERALLBATTERYBefore CalibrationAft
Page 90 and 91:
19. Run Time Error MessagesRun Time
Page 92 and 93:
21. Appendix A: BCT-128 Parts ListQ
Page 94 and 95:
23. Appendix C: Spare PartsBCT-2000
Page 96 and 97:
constant power button .............
Page 98:
Ssafety information ...............
show all

BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?