Lambda 20/Lambda 40 Installation and Maintenance Guide - VTP UP

More documents

Recommendations

Info

Lambda 20, Lambda 40 UV/Vis SpectrometersIEC 1010 ComplianceThis instrument has been designed and tested in accordance with IEC 1010-1: Safetyrequirements for electrical equipment for measurement, control, and laboratory use,and Amendment 1 to this standard.CSA ComplianceThis instrument meets the Canadian Standards Association (CSA) StandardCAN/CSA-C22.2 No. 1010.1-92: Laboratory Equipment.UL ComplianceThis instrument meets the Underwriter Laboratories (UL) Standard UL 3101-1/Oct.93: Electrical Equipment for laboratory use, part 1: general requirements.Electrical ProtectionInsulation: Class I as defined in IEC 1010-1.Installation Category: The instruments are able to withstand transient overvoltageaccording to Installation Category II as defined in IEC 1010-1 and IEC 664.Pollution Degree: The equipment will operate safely in environments that containnon-conductive foreign matter and condensation up to Pollution Degree 2 as definedin IEC 1010-1 and IEC 664.Electrical SafetyTo ensure satisfactory and safe operation of the instrument, it is essential that thegreen/yellow lead of the line power cord is connected to true electrical earth(ground).If any part of the instrument is not installed by a PerkinElmer service representative,make sure that the line power plug is wired correctly:8
Safety InformationTerminalCord Lead ColorsInternationalUSALive Brown BlackNeutral Blue WhiteProtective Conductor(earth/ground)Green/YellowGreenWARNINGElectrical HazardAny interruption of the protective conductor inside or outside theinstrument or disconnection of the protective conductor (earth/ground)terminal is likely to make the instrument dangerous.International interruption is prohibited.Lethal voltages are present in the instrument• Even with the power switch OFF, line power voltages can still bepresent within the instrument.• When the instrument is connected to line power, terminals may belive, and opening covers or removing parts (except those to whichaccess can be gained without the use of a tool) is likely to exposelive parts.• Capacitors inside the instrument may still be charged even if theinstrument has been disconnected from all voltage sources.When working with the instrument:• Connect the instrument to a correctly installed line power outlet that has aprotective conductor (earth/ground).• Do not attempt to make internal adjustments ore replacements except asdirected in this handbook.• Do not operate the instrument with any covers or parts removed.9
Page 2: Release HistoryPart Number Release
Page 5: Safety Information 1
Page 10 and 11: Lambda 20, Lambda 40 UV/Vis Spectro
Page 19 and 20: PrefacePrefaceApplicationThe Lambda
Page 21: Basic Installation 3
Page 24: Lambda 20, Lambda 40 UV/Vis Spectro
Page 39 and 40: Accessory InstallationAccessory Ins
Page 41 and 42: Accessory InstallationJ88, Sphere I
Page 43 and 44: Accessory InstallationLinear Transp
Page 45 and 46: Accessory InstallationMulti-sippers
Page 47 and 48: Accessory InstallationPersonal Comp
Page 49: Maintenance 5
Page 59 and 60:
Maintenance5. Remove the lamp assem
Page 61 and 62:
MaintenanceLamp baffleThumbscrew(de
Page 63 and 64:
MaintenanceWARNINGElectrical Hazard
Page 65 and 66:
MaintenanceChanging FusesWARNINGEle
Page 67 and 68:
Maintenance5. Press 4 Print to feed
Page 69:
Replacement Parts 6
Page 72 and 73:
Lambda 20, Lambda 40 UV/Vis Spectro
Page 75 and 76:
System DescriptionSystem Descriptio
Page 77 and 78:
System DescriptionHalogenlampM2M =
Page 79 and 80:
System DescriptionThe radiation is
Page 81:
Technical Data 8
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 93 and 94:
Translations of WarningsTranslation
Page 95 and 96:
Translations of Warnings95
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103:
Index 10
Page 106:
show all

Lambda 20/Lambda 40 Installation and Maintenance Guide - VTP UP

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?