Lambda 20/Lambda 40 Installation and Maintenance Guide - VTP UP

More documents

Recommendations

Info

Lambda 20, Lambda 40 UV/Vis SpectrometersWhen the cell holder has been aligned once, you can take it out and reinstall itwithout aligning it again.Minimum Volume ApplicationsTo measure minimum sample volumes, use microcells (offered by PerkinElmer).The minimum sample volume required is a function of the cell internal width orvolume and is specified below.Cell TypeCellInternalWidthPathlengthMinimumVolumeRequiredPartNumberHeight ofliquid slightlymore thanheight ofbeam2 mm 1 cm 200 µL B0631071(pair)4 mm 1 cm 400 µL B0631064(pair)CellVolumePathlengthMinimumVolumeRequiredPartNumberCell windowcompletelyfilled withliquid0.5 µL 0.01 cm 2 µL B06310822.5 µL 0.5 cm 5 µL B06310805 µL 0.1 cm 10 µL B06310835 µL 1.0 cm 10 µL B063108130 µL 1.0 cm 50 µL B063107934
Basic InstallationNOTE: You should align microcells very carefully in the radiation beam by following theprocedures in Aligning the Single Cell Holder on page 31. When aligningmicrocells, fill each cell with the minimum volume of liquid specified in the abovetable to make sure that the liquid meniscus is not in the radiation beam.Setting up the PrinterActivating the Internal PrinterIf you want to use the internal printer, make sure the method PRINTER CONFIG. isset to EPSON/INTERNAL in Super User. On delivery, the default setting isEPSON/INTERNAL.Connecting an External PrinterYou can use an external printer for hard-copy printouts of the analytical results.PerkinElmer offers suitable printers; refer to the current price list for details.To install an external printer:1. Switch off the spectrometer, if it is on.2. Set up the printer as given in the User’s Guide provided with the printer.3. Configure the printer.4. Connect the printer to the Parallel Port.If you connect the printer to the second RS 232 interface, make sure theInstrument Configuration method is set correctly in Super User.5. Switch on the spectrometer and the printer to activate the new printerconfiguration.6. Make sure the method PRINTER CONFIG. is set correctly for the connectedprinter in Super User.35
Page 2: Release HistoryPart Number Release
Page 5: Safety Information 1
Page 8 and 9: Lambda 20, Lambda 40 UV/Vis Spectro
Page 19 and 20: PrefacePrefaceApplicationThe Lambda
Page 21: Basic Installation 3
Page 24: Lambda 20, Lambda 40 UV/Vis Spectro
Page 39 and 40: Accessory InstallationAccessory Ins
Page 41 and 42: Accessory InstallationJ88, Sphere I
Page 43 and 44: Accessory InstallationLinear Transp
Page 45 and 46: Accessory InstallationMulti-sippers
Page 47 and 48: Accessory InstallationPersonal Comp
Page 49: Maintenance 5
Page 59 and 60: Maintenance5. Remove the lamp assem
Page 61 and 62: MaintenanceLamp baffleThumbscrew(de
Page 63 and 64: MaintenanceWARNINGElectrical Hazard
Page 65 and 66: MaintenanceChanging FusesWARNINGEle
Page 67 and 68: Maintenance5. Press 4 Print to feed
Page 69: Replacement Parts 6
Page 75 and 76: System DescriptionSystem Descriptio
Page 77 and 78: System DescriptionHalogenlampM2M =
Page 79 and 80: System DescriptionThe radiation is
Page 81: Technical Data 8
Page 84 and 85:
Lambda 20, Lambda 40 UV/Vis Spectro
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 93 and 94:
Translations of WarningsTranslation
Page 95 and 96:
Translations of Warnings95
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103:
Index 10
Page 106:
show all

Lambda 20/Lambda 40 Installation and Maintenance Guide - VTP UP

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?