Lambda 20/Lambda 40 Installation and Maintenance Guide - VTP UP

More documents

Recommendations

Info

Lambda 20, Lambda 40 UV/Vis SpectrometersConnecting to the Electrical SupplyElectrical HazardWARNING• To prevent potential injury to yourself and damage to theinstrument, first make the electrical connections between theinstruments in the system before connecting to the line powersupply.• The spectrometer automatically adjusts to the correct operatingvoltage.Before starting the instrument for the first time, make sure that thecorrect fuse is fitted to your line power supply.If you have a different fuse, change it for the correct one.Do not connect the spectrometer to the line power supply if thewrong fuse is fitted.1. Make sure that the correct fuses are fitted in the holder at the rear of thespectrometer (see Changing Fuses on page 65).VoltageStandard100 V – 120 V 6.3 A slow-blow210 V – 240 V 3.15 A slow-blowNOTE: The module has two fuses.2. Make sure that the plug fitted to the line power cord provided with thespectrometer is suitable for your local electrical outlets.If it is not, remove it and fit a plug conforming to the local regulations.3. After all connections have been made between the various components of thesystem, make certain that all power switches are set to off, then connect theline cords to the electrical power supply.The power switch is located at the top right-hand rear of the spectrometer.28
Basic InstallationNOTE: To prevent interferences caused by earth loops when operating with ancillaryinstruments (printers, etc.), connect all components of the system to the same phaseof the electrical supply via a multisocket distributor.Single Cell HolderLocking screwfor horizontalalignmentVertical adjustmentscrewLifterMilled postLocking screwfor horizontalalignmentFigure 6 Single Cell Holder B0505071NOTE: Depending on the spectrometer, the single cell holder can be installed in twodifferent positions in the sample compartment. Always install the holder such thatthe arrow on the cell holder lines up with the center point on the baseplate (seeInstalling the Cell Holder on page 30).29
Page 2: Release HistoryPart Number Release
Page 5: Safety Information 1
Page 8 and 9: Lambda 20, Lambda 40 UV/Vis Spectro
Page 19 and 20: PrefacePrefaceApplicationThe Lambda
Page 21: Basic Installation 3
Page 24: Lambda 20, Lambda 40 UV/Vis Spectro
Page 39 and 40: Accessory InstallationAccessory Ins
Page 41 and 42: Accessory InstallationJ88, Sphere I
Page 43 and 44: Accessory InstallationLinear Transp
Page 45 and 46: Accessory InstallationMulti-sippers
Page 47 and 48: Accessory InstallationPersonal Comp
Page 49: Maintenance 5
Page 59 and 60: Maintenance5. Remove the lamp assem
Page 61 and 62: MaintenanceLamp baffleThumbscrew(de
Page 63 and 64: MaintenanceWARNINGElectrical Hazard
Page 65 and 66: MaintenanceChanging FusesWARNINGEle
Page 67 and 68: Maintenance5. Press 4 Print to feed
Page 69: Replacement Parts 6
Page 75 and 76: System DescriptionSystem Descriptio
Page 77 and 78: System DescriptionHalogenlampM2M =
Page 79 and 80:
System DescriptionThe radiation is
Page 81:
Technical Data 8
Page 84 and 85:
Lambda 20, Lambda 40 UV/Vis Spectro
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 93 and 94:
Translations of WarningsTranslation
Page 95 and 96:
Translations of Warnings95
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103:
Index 10
Page 106:
show all

Lambda 20/Lambda 40 Installation and Maintenance Guide - VTP UP

Create successful ePaper yourself

Delete template?

Save as template?