TM9-2815-226-34-1 - JATONKAM35s HOME ON THE WEB

More documents

Recommendations

Info

TM 9-2815-226-34-1Section IV. CYLINDER LINERS INSPECTION3-10. CLEAN LINERSCAUTIONSTAY CLEAR OF SEAL RING GROOVES WITH WIRE BRUSH. MAY DAMAGEGROOVES.NOTECylinder liners are in direct contact with coolant for efficient cooling. Coolant issealed in block by machined surfaces at liner flange and by O-rings and creviceseal at lower end of liner.a. Remove rust and scale from exterior of liner. Stay clear of seal grooves.b. Clean exterior of liner with bristle (not wire) scrub brush and warm water and detergent soap.c. Wash interior with detergent soap and warm water using bristle (not wire) scrub brush.WARNINGCOMPRESSED AIR USED FOR CLEANING PURPOSES WILL NOT EXCEED 30 PSI(207 KPA). USE ONLY WITH EFFECTIVE CHIP GUARDING AND PERSONALPROTECTIVE EQUIPMENT (GOGGLES, SHIELD, GLOVES, ETC.).d. Rinse liners thoroughly and dry with compressed air.e. Coat liner interior with engine oil and let stand for 5 to 10 minutes.f. Use white paper towels to wipe oil from inside of liners. Note gray or black residue that appears with oil on whitetowels.g. Repeat application of engine oil and wipe off with towels until residue no longer shows.3-115
TM 9-2815-226-34-13-11. INSPECT LINERSa. Using magnetic particle method, inspect liner just under top flange, bottom of liner, and above top seal ringgroove for cracks. Discard cracked liners.b. Check exterior of liner for excessive corrosion or erosion and pits 1/16 in. (1.59 mm) deep or more. Discard ifdefective.c. Check liners for dents, pitting, or fretting on underside of top flange. Discard if defective.d. Check liners for wear with dial bore gage. Discard liner if inside diameter exceeds 5.505 in. (139. 827 mm).3-116
Page 5 and 6:
WARNINGFIRE AND EXPLOSIONDo not use
Page 7 and 8:
TM 9-2815-226-34-1TECHNICAL MANUALN
Page 9 and 10:
TM 9-2815-226-34-1CHAPTER 1INTRODUC
Page 11 and 12:
TM 9-2815-226-34-11-7. LOCATION AND
Page 13 and 14:
TM 9-2815-226-34-11-9. EQUIPMENT DA
Page 15 and 16:
TM 9-2815-226-34-1CHAPTER 2MAINTENA
Page 17 and 18:
TM 9-2815-226-34-1Table 2-1. TROUBL
Page 19 and 20:
TM 9-2815-226-34-1Table 2-1. TROUBL
Page 21 and 22:
TM 9-2815-226-34-1Table 2-1. TROUBL
Page 23 and 24:
TM 9-2815-226-34-1Table 2-1. TROUBL
Page 25 and 26:
TM 9-2815-226-34-1Table 2-1. TROUBL
Page 27 and 28:
TM 9-2815-226-34-1Table 2-1. TROUBL
Page 30:
TM 9-2815-226-341Table 2-1. TROUBLE
Page 33 and 34:
TM 9-2815-226-34-1Table 2-1. TROUBL
Page 35 and 36:
TM 9-2815-226-34-1Table 2-1. TROUBL
Page 37 and 38:
TM 9-2815-226-34-1Table 2-1. TROUBL
Page 39 and 40:
TM 9-2815-226-34-1CHAPTER 3REPAIR O
Page 41 and 42:
TM 9-2815-226-34-13-3. INSPECTIONa.
Page 43 and 44:
TM 9-2815-226-34-1Table 3-1. REPAIR
Page 45 and 46:
TM 9-2815-226-34-1Table 3-1. REPAIR
Page 47 and 48:
TM 9-2815-226-34-1Table 3-1. REPAIR
Page 49 and 50:
TM 9-2815-226-34-1Table 3-1. REPAIR
Page 51 and 52:
TM 9-2815-226-34-1WATER PUMPImpelle
Page 53 and 54:
TM 9-2815-226-34-1Table 3-1. REPAIR
Page 55 and 56:
TM 9-2815-226-34-1f. Bushings and B
Page 57 and 58:
TM 9-2815-226-34-1NOTEAll replaceme
Page 59 and 60:
TM 9-2815-226-34-1Table 3-3. TORQUE
Page 61 and 62:
TM 9-2815-226-34-1TABLE 3-3. TORQUE
Page 63 and 64:
TM 9-2815-226-34-1TABLE 3-3. TORQUE
Page 65 and 66:
TM 9-2815-226-34-1TABLE 3-3. TORQUE
Page 67 and 68:
TM 9-2815-226-34-1f. Remove Remaini
Page 69 and 70:
TM 9-2815-226-34-1(13) Remove Vibra
Page 71 and 72:
TM 9-2815-226-34-1(18) Remove Lube
Page 73 and 74:
TM 9-2815-226-34-1(20) Remove Front
Page 75 and 76:
TM 9-2815-226-34-1(23) Remove Rocke
Page 77 and 78:
TM 9-2815-226-34-1(f)Carefully tap
Page 79 and 80:
TM 9-2815-226-34-1(25) Remove Cam F
Page 81 and 82:
TM 9-2815-226-34-1(27) Remove Flywh
Page 83 and 84:
TM 9-2815-226-34-1(29) Remove Rear
Page 85 and 86:
TM 9-2815-226-34-1(31) Remove Camsh
Page 87 and 88:
TM 9-2815-226-34-1NOTEKeep rod caps
Page 89 and 90:
TM 9-2815-226-34-1(33) Crankshaft a
Page 91 and 92:
TM 9-2815-226-34-1CAUTIONHANDLE CRA
Page 93 and 94:
TM 9-2815-226-34-1(35) Remove and D
Page 95 and 96:
TM 9-2815-226-34-1Section III. CYLI
Page 97 and 98:
TM 9-2815-226-34-1WARNINGHOT TANK C
Page 99 and 100:
TM 9-2815-226-34-1g. Check camshaft
Page 101 and 102:
TM 9-2815-226-34-1(9) If any one in
Page 103 and 104: TM 9-2815-226-34-1(5) If liner to b
Page 105 and 106: TM 9-2815-226-34-1m. Check main bea
Page 107 and 108: TM 9-2815-226-34-1(2) Install ST-11
Page 109 and 110: TM 9-2815-226-34-1o. Check cylinder
Page 111 and 112: TM 9-2815-226-34-1b. Cylinder liner
Page 113 and 114: TM 9-2815-226-34-1(i)(j)(k)Rotate c
Page 115 and 116: TM 9-2815-226-34-1(u)(v)(w)(x)(y)(z
Page 117 and 118: TM 9-2815-226-34-1(d)(e)Place salva
Page 119 and 120: TM 9-2815-226-34-1(f)(g)Back off th
Page 121 and 122: TM 9-2815-226-34-1(3) Cut counterbo
Page 123 and 124: TM 9-2815-226-34-1NOTEReplacement s
Page 125 and 126: TM 9-2815-226-34-1(g)(h)Tighten adj
Page 127 and 128: TM 9-2815-226-34-1(4) Install count
Page 129 and 130: TM 9-2815-226-34-1f. Cylinder liner
Page 131 and 132: TM 9-2815-226-34-1(2) Assemble micr
Page 133 and 134: TM 9-2815-226-34-1(3) Feed assembly
Page 135 and 136: TM 9-2815-226-34-1(k)(l)Install too
Page 137 and 138: TM 9-2815-226-34-1(5) Main bearing
Page 139 and 140: TM 9-2815-226-34-1NOTESpecial lockr
Page 141 and 142: TM 9-2815-226-34-1(d)(e)(f)(g)(h)(i
Page 143 and 144: TM 9-2815-226-34-1(m)(n)(o)(p)(q)(r
Page 145 and 146: TM 9-2815-226-34-1j. Cylinder Block
Page 147 and 148: TM 9-2815-226-34-1(8) Apply cutting
Page 149 and 150: TM 9-2815-226-34-1CAUTIONTAKE CARE
Page 151 and 152: TM 9-2815-226-34-1(8) Apply cutting
Page 153: TM 9-2815-226-34-1(3) With surface
Page 157 and 158: TM 9-2815-226-34-13-13. INSPECT CRA
Page 159 and 160: TM 9-2815-226-34-1k. Measure cranks
Page 161 and 162: TM 9-2815-226-34-1(2) Indications l
Page 163 and 164: TM 9-2815-226-34-1p. Perform magnet
Page 165 and 166: TM 9-2815-226-34-1Section VI. BEARI
Page 167 and 168: TM 9-2815-226-34-13-17. INSPECT CON
Page 169 and 170: TM 9-2815-226-34-1NOTECheck connect
Page 171 and 172: TM 9-2815-226-34-1(3) To determine
Page 173 and 174: TM 9-2815-226-34-13-18. REPAIR CONN
Page 175 and 176: TM 9-2815-226-34-1NOTEBoring machin
Page 177 and 178: TM 9-2815-226-34-1d. Install piston
Page 179 and 180: TM 9-2815-226-34-1Section VIII. PIS
Page 181 and 182: TM 9-2815-226-34-13-20. INSPECT PIS
Page 183 and 184: TM 9-2815-226-34-1g. Discard piston
Page 185 and 186: TM 9-2815-226-34-1Section IX. CAMSH
Page 187 and 188: TM 9-2815-226-34-13-25. REPAIR CAMS
Page 189 and 190: TM 9-2815-226-34-1Section X. GEAR C
Page 191 and 192: TM 9-2815-226-34-13-29. REPAIR GEAR
Page 193 and 194: TM 9-2815-226-34-1CAUTIONTAKE CARE
Page 195 and 196: TM 9-2815-226-34-13-30. DISASSEMBLE
Page 197 and 198: WARNINGP-D-680 SOLVENT IS POTENTIAL
Page 199 and 200: TM 9-2815-226-34-1(7) Place head an
Page 201 and 202: TM 9-2815-226-34-1(7) With shut-off
Page 203 and 204: TM 9-2815-226-34-1f. Injector sleev
Page 205 and 206:
TM 9-2815-226-34-1(2) Gage at sever
Page 207 and 208:
TM 9-2815-226-34-1i. Valve inspecti
Page 209 and 210:
TM 9-2815-226-34-1k. Valve springs
Page 211 and 212:
TM 9-2815-226-34-1(5) Insert ST-101
Page 213 and 214:
TM 9-2815-226-34-1(21) Aline sleeve
Page 215 and 216:
TM 9-2815-226-34-1(5) Make light cu
Page 217 and 218:
TM 9-2815-226-34-1(16) Allow cutter
Page 219 and 220:
TM 9-2815-226-34-1(3) Engage ST-685
Page 221 and 222:
TM 9-2815-226-34-1(6) If high spots
Page 223 and 224:
TM 9-2815-226-34-1(3) Install overs
Page 225 and 226:
TM 9-2815-226-34-1(3) Raise arbor p
Page 227 and 228:
TM 9-2815-226-34-1(i)(j)(k)(l)(m)(n
Page 229 and 230:
TM 9-2815-226-34-1(3) Expand inject
Page 231 and 232:
TM 9-2815-226-34-1(h)(i)Cut injecto
Page 233 and 234:
TM 9-2815-226-34-1b. Install valves
Page 235 and 236:
TM 9-2815-226-34-1c. Valve seating
Page 237 and 238:
TM 9-2815-226-34-1(16) If leakage i
Page 239 and 240:
TM 9-2815-226-34-1NOTETag rocker le
Page 241 and 242:
TM 9-2815-226-34-13-34. INSPECT ROC
Page 243 and 244:
TM 9-2815-226-34-1NOTEUse magnetic
Page 245 and 246:
TM 9-2815-226-34-13-35. REPAIR ROCK
Page 247 and 248:
TM 9-2815-226-34-13-36. ASSEMBLE RO
Page 249 and 250:
TM 9-2815-226-34-1Section XIII. PUS
Page 251 and 252:
TM 9-2815-226-34-1Section XIV. CAM
Page 253 and 254:
TM 9-2815-226-34-1b. Inspect housin
Page 255 and 256:
TM 9-2815-226-34-1d. Inspect cam fo
Page 257 and 258:
TM 9-2815-226-34-1NOTEInjector cam
Page 259 and 260:
TM 9-2815-226-34-1(7) Slide ST-249-
Page 261 and 262:
TM 9-2815-226-34-13-41. ASSEMBLE CA
Page 263 and 264:
TM 9-2815-226-34-13-42. INSPECT VIB
Page 265 and 266:
TM 9-2815-226-34-1Section XVI. FLEX
Page 267 and 268:
TM 9-2815-226-34-1ALPHABETICAL INDE
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 279 and 280:
THE METRIC SYSTEM AND EQUIVALENTSLI
show all

TM9-2815-226-34-1 - JATONKAM35s HOME ON THE WEB

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?