SkyView System Installation Guide - Dynon Avionics
SkyView System Installation Guide - Dynon Avionics SkyView System Installation Guide - Dynon Avionics
SV-D700 / SV-D1000 Installation and ConfigurationIn the event of an electrical failure that causes SkyView to run on the SV-BAT-320, the SV-BAT-320 supplies power to the SkyView display it is connected to, along with any connected SV-ADAHRS-20X, SV-EMS-220/221, SV-ARINC-429, and SV-GPS-250 modules. A fully charged SV-BAT-320 can keep most SkyView systems operating for at least 60 minutes. The SV-BAT-320does not supply (backup) power to the following SkyView system devices:Autopilot servosHeated AOA/Pitot ProbeSV-ADSB-470SV-COM-425SV-XPNDR-26XAny non-Dynon deviceSkyView displays are only compatible with Dynon’s SV-BAT-320 backup battery. Donot connect a lead-acid battery or any other battery to the connection reserved forthe SV-BAT-320 as the charging algorithm is optimized for the SV-BAT-320.Connecting any other battery may have detrimental consequences. Damagecaused by connecting such a battery will not be repaired under warranty.See the Homemade Wire Harness Considerations section for importantspecifications that must be adhered to for the SV-BAT-320 to charge properlywhen used with a non-Dynon harness.SkyView Network ConnectorsThe two D9 connectors on the back of a SkyView display are SkyView network connectors. Theyhave identical pin-outs and are electrically connected inside the display (i.e., they arecompletely interchangeable). Installers may use either connector or both connectors in SkyViewinstallations. Reference Table 64 on page 19-8 for SkyView Network Connector pin-outinformation.Note that these connectors are not serial port connectors.Network Setup and StatusOnce all SkyView modules are connected in a network, either in a bench top test or permanentinstallation, turn the display(s) on. You will see the display boot up and the status LEDs on themodules light up.A tail number on the Aircraft Information Page (SETUP MENU > SYSTEM SETUP >AIRCRAFT INFORMATION) is required for network configuration.If you have more than one display in your SkyView system, the tail number onlyneeds to be set on the display that you initially perform the Network Configurationon. At network configuration time, all other displays that are set to the default tail4-8 SkyView System Installation Guide - Revision O
SV-D700 / SV-D1000 Installation and Configurationnumber of DYNON will automatically have their settings and tail numbersynchronized with the display the configuration is performed from. Afterconfiguration, all displays’ tail numbers and settings will be synchronized, andfurther setup tasks can be performed from any display.Before you configure the SkyView network, the PFD and EMS pages will contain abig red “X” over a black screen. You must configure the network before PFD andEMS data is displayed on SkyViewUse the following procedure to configure a SkyView network:1. Navigate to the CONFIGURE… Page (SETUP MENU > SYSTEM SETUP > NETWORK SETUP> CONFIGURE…).2. Press DETECT. A successful network configuration yields the screen in Figure 20.3. Press FINISH to close the screen and return to the Network Setup Menu.Figure 20–Successful SkyView Network Configuration ScreenIf the SkyView network is successfully configured, but firmware versions onequipment are not synchronized, you will see a screen that is similar to Figure 21.SkyView System Installation Guide - Revision O 4-9
- Page 13 and 14: Table of ContentsTachometer .......
- Page 15: Table of Contents19. Appendix C: Wi
- Page 18 and 19: IntroductionAbout this GuideIn the
- Page 21 and 22: 2. System PlanningInstallers should
- Page 23 and 24: System PlanningTemperature Specific
- Page 25 and 26: System PlanningIn order to provide
- Page 27 and 28: System Planningferrous material suc
- Page 29 and 30: SV-XPNDR-26XSystem PlanningThe SV-X
- Page 31 and 32: System PlanningSkyView System Const
- Page 33 and 34: System PlanningTest SkyView Network
- Page 35 and 36: System PlanningDynon Part NumberSV-
- Page 37 and 38: System PlanningFigure 8- SkyView Sy
- Page 39: System PlanningSoftware is in use.
- Page 42 and 43: Basic SkyView Display OperationDisp
- Page 44 and 45: Basic SkyView Display OperationA bu
- Page 46 and 47: Basic SkyView Display OperationBasi
- Page 48 and 49: Basic SkyView Display OperationYou
- Page 50 and 51: Basic SkyView Display Operationthis
- Page 52 and 53: Basic SkyView Display OperationFlig
- Page 54 and 55: Basic SkyView Display OperationFirm
- Page 57 and 58: 4. SV-D700 / SV-D1000 Installation
- Page 59 and 60: SV-D700 / SV-D1000 Installation and
- Page 61 and 62: SV-D700 / SV-D1000 Installation and
- Page 63: SV-D700 / SV-D1000 Installation and
- Page 67 and 68: Internal Time KeepingSV-D700 / SV-D
- Page 69 and 70: SV-D700 / SV-D1000 Installation and
- Page 71 and 72: SV-D700 / SV-D1000 Installation and
- Page 73 and 74: SV-D700 / SV-D1000 Installation and
- Page 75 and 76: SV-D700 / SV-D1000 Installation and
- Page 77 and 78: SV-D700 / SV-D1000 Installation and
- Page 79 and 80: SV-D700 / SV-D1000 Installation and
- Page 81 and 82: SV-D700 / SV-D1000 Installation and
- Page 83 and 84: 5. SV-ADAHRS-20X Installation and C
- Page 85 and 86: SV-ADAHRS-20X Installation and Conf
- Page 87 and 88: SV-OAT-340 Location and Installatio
- Page 89 and 90: Measurement UnitsSV-ADAHRS-20X Inst
- Page 91 and 92: SV-ADAHRS-20X Installation and Conf
- Page 93 and 94: 6. SV-MAP-270 Navigation Mapping So
- Page 95 and 96: SV-ADAHRS-20X Installation and Conf
- Page 97: SV-ADAHRS-20X Installation and Conf
- Page 100 and 101: SV-EMS-220/221 Installation and Con
- Page 102 and 103: SV-EMS-220/221 Installation and Con
- Page 104 and 105: SV-EMS-220/221 Installation and Con
- Page 106 and 107: SV-EMS-220/221 Installation and Con
- Page 108 and 109: SV-EMS-220/221 Installation and Con
- Page 110 and 111: SV-EMS-220/221 Installation and Con
- Page 112 and 113: SV-EMS-220/221 Installation and Con
SV-D700 / SV-D1000 <strong>Installation</strong> and Configurationnumber of DYNON will automatically have their settings and tail numbersynchronized with the display the configuration is performed from. Afterconfiguration, all displays’ tail numbers and settings will be synchronized, andfurther setup tasks can be performed from any display.Before you configure the <strong>SkyView</strong> network, the PFD and EMS pages will contain abig red “X” over a black screen. You must configure the network before PFD andEMS data is displayed on <strong>SkyView</strong>Use the following procedure to configure a <strong>SkyView</strong> network:1. Navigate to the CONFIGURE… Page (SETUP MENU > SYSTEM SETUP > NETWORK SETUP> CONFIGURE…).2. Press DETECT. A successful network configuration yields the screen in Figure 20.3. Press FINISH to close the screen and return to the Network Setup Menu.Figure 20–Successful <strong>SkyView</strong> Network Configuration ScreenIf the <strong>SkyView</strong> network is successfully configured, but firmware versions onequipment are not synchronized, you will see a screen that is similar to Figure 21.<strong>SkyView</strong> <strong>System</strong> <strong>Installation</strong> <strong>Guide</strong> - Revision O 4-9