SkyView System Installation Guide - Dynon Avionics

More documents

Recommendations

Info

Appendix A: Maintenance and TroubleshootingAnnual Backup Battery TestPerform this test to ensure each backup battery in the SkyView system is fully functional. A fullycharged SV-BAT-320 should power a typical SkyView system for at least 60 minutes if primarypower is lost.If the SkyView system has more than one display with a backup battery installed, perform thetest for each display individually. Power off all but one display during the test.Test Procedure1. Fully charge the SV-BAT-320 Backup Battery. Reference the Battery Charging section ofthe SV-BAT-320 Installation chapter of this manual. Disconnect primary power from theSkyView display—ensure that the display is not powered from another source.2. Press TEST BAT button3. The BATTERY TEST screen will appear displaying the status of the test. Note that whilethe test will last 60 minutes, if the SV-BAT-320 is able to power the system for at least45 minutes, the battery is normal.4. The BATTERY TEST can be aborted by pressing the PWR OFF button.Repeat the test procedure for each backup battery in the system.This test discharges the backup battery. Recharging the battery after the test isrecommended. Do this by applying primary power to the display. The backupbattery is fully charged when its voltage reaches 12.25 volts.If a tested battery does not pass the initial backup battery test, please contact Dynon Avionicsby phone or the online store (store.dynonavionics.com) to obtain a replacement battery.Please dispose of non‐functional SkyView backup batteries in a responsiblemanner. SkyView backup batteries are lithium-ion and similar in construction tocordless tool batteries. They can likely be recycled wherever cordless tool batteryrecycling is available. For a list of recycling locations in your area (USA only), call 1-800-8-BATTERY or see the Call 2 Recycle website at www.rbrc.org.TroubleshootingThe Display Hardware Information Page (SETUP MENU > LOCAL DISPLAY SETUP > DISPLAYHARDWARE INFORMATION) can be a valuable resource when troubleshooting SkyView and isdescribed in the previous section.If the suggestions below do not help, or your issue is not listed below, please callDynon Technical Support at +1(425) 402-0433 or email atsupport@dynonavionics.com.17-8 SkyView System Installation Guide - Revision O
Appendix A: Maintenance and TroubleshootingNetwork Configuration Does Not Work or SkyView Network Module Is Not WorkingProperlyIf you try and configure a SkyView network and it does not work, try the following:Check network wiring and try again. There may be a short or an open somewhere.Unplug network modules one by one and try again. It is possible that one of themodules could cause the network to stop functioning.Try again.For modules such as the SV-ADAHRS-20X, the SV-EMS-220/221, and SV-ARINC-429,observe the red LED light near the SkyView Network connector:o Flashing Fast: The module is operating normally and is configured andcommunicating on a SkyView Network.o Flashing Slowly: The module is operating normally, but is not active on SkyViewNetwork.o Off: The module is not receiving power (from a SkyView Network / Display)o On Solid - the module is receiving power, but is not operating normally.SkyView Reports STANDBY NETWORK ERRORSkyView has detected a problem with the SkyView Network wiring between one or moremodules. Go to SETUP MENU > SYSTEM SETUP > NETWORK SETUP > NETWORK STATUS for adescription of the problem. Module failures and/or wiring faults (via SkyView D9 connector pincallouts) will be annunciated here to aid troubleshooting. The fault will be below thecomponent(s) that SkyView can see the fault in. This may help you narrow down the wiring runor connector that is faulty.For example, a “Connection Fault: 4/8” listed below an SV-ADAHRS-200 listing in the networkstatus page means that pins 4 and 8 on a SkyView Network harness or connector that goes tothat component has a connectivity problem. This could be a broken wire, swapped wires, badconnection, etc, and should be analyzed with a multimeter or other direct method.If the fault were instead listed under a SkyView display listing in the network status page, thatmeans that the fault is seen on devices connected to that display, and is likely due to aconnectivity issue at or very near the display in your SkyView Network wiring scheme.Compass Calibration FailsIf you try to calibrate your compass and it does not work, try the following:Ensure SkyView is receiving data from the system’s GPS receiver. Go to the DisplayHardware Information Page as mentioned at the beginning of this section, scroll downthe menu to the serial port status section, and confirm that the receive (RX) counter isactive on the GPS serial port.Ensure the SkyView network status includes the ADAHRS you’re trying to calibrate. Usethe Network Status Wizard and confirm that the ADAHRS is present in the system.Ensure the ADAHRS location is compatible with the requirements outlined in theGeneral System Installation Tips Section of this guide.SkyView System Installation Guide - Revision O 17-9
Page 1:
SkyViewSystem Installation GuideThi
Page 6 and 7:
Revision Revision Date Descriptionh
Page 8 and 9:
Revision Revision Date DescriptionC
Page 11 and 12:
Table of ContentsContact Informatio
Page 13 and 14:
Table of ContentsTachometer .......
Page 15:
Table of Contents19. Appendix C: Wi
Page 18 and 19:
IntroductionAbout this GuideIn the
Page 21 and 22:
2. System PlanningInstallers should
Page 23 and 24:
System PlanningTemperature Specific
Page 25 and 26:
System PlanningIn order to provide
Page 27 and 28:
System Planningferrous material suc
Page 29 and 30:
SV-XPNDR-26XSystem PlanningThe SV-X
Page 31 and 32:
System PlanningSkyView System Const
Page 33 and 34:
System PlanningTest SkyView Network
Page 35 and 36:
System PlanningDynon Part NumberSV-
Page 37 and 38:
System PlanningFigure 8- SkyView Sy
Page 39:
System PlanningSoftware is in use.
Page 42 and 43:
Basic SkyView Display OperationDisp
Page 44 and 45:
Basic SkyView Display OperationA bu
Page 46 and 47:
Basic SkyView Display OperationBasi
Page 48 and 49:
Basic SkyView Display OperationYou
Page 50 and 51:
Basic SkyView Display Operationthis
Page 52 and 53:
Basic SkyView Display OperationFlig
Page 54 and 55:
Basic SkyView Display OperationFirm
Page 57 and 58:
4. SV-D700 / SV-D1000 Installation
Page 59 and 60:
SV-D700 / SV-D1000 Installation and
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Internal Time KeepingSV-D700 / SV-D
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
5. SV-ADAHRS-20X Installation and C
Page 85 and 86:
SV-ADAHRS-20X Installation and Conf
Page 87 and 88:
SV-OAT-340 Location and Installatio
Page 89 and 90:
Measurement UnitsSV-ADAHRS-20X Inst
Page 91 and 92:
Page 93 and 94:
6. SV-MAP-270 Navigation Mapping So
Page 95 and 96:
Page 97:
Page 100 and 101:
SV-EMS-220/221 Installation and Con
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 165 and 166:
8. SV-GPS-250 Installation and Conf
Page 167 and 168:
SV-GPS-250 Installation and Configu
Page 169 and 170:
9. SV-BAT-320 InstallationThis chap
Page 171 and 172:
SV-BAT-320 Installationvoltages to
Page 173:
SV-BAT-320 InstallationTest Procedu
Page 176 and 177:
Autopilot Servo Installation, Confi
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 197 and 198:
11. SV-XPNDR-26X Installation, Conf
Page 199 and 200:
SV-XPNDR-26X Installation, Configur
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Post Installation ChecksSV-XPNDR-26
Page 217 and 218:
12. SV-ARINC-429 Installation and C
Page 219 and 220:
SV-ARINC-429 Installation and Confi
Page 221 and 222:
ARINC Device ConnectionsSV-ARINC-42
Page 223 and 224:
Page 225:
Page 228 and 229:
Vertical Power VP-X Integration and
Page 230 and 231: Vertical Power VP-X Integration and
Page 233 and 234: 14. SV-ADSB-470 Installation, Confi
Page 235 and 236: SV-ADSB-470 Installation, Configura
Page 241: Post Installation ChecksSV-ADSB-470
Page 244 and 245: Accessory Installation and Configur
Page 258 and 259: SV-COM-C25 Installation, Configurat
Page 274 and 275: Appendix A: Maintenance and Trouble
Page 284 and 285: Appendix B: SpecificationsSkyView E
Page 286 and 287: Appendix B: SpecificationsSV-XPNDR-
Page 288 and 289: Appendix B: SpecificationsSV-COM-C2
Page 290 and 291: Appendix C: Wiring and Electrical C
Page 309 and 310: 20. Appendix D: SV-EMS-220/221 Sens
Page 311 and 312: 21. Appendix E: Serial Data OutputA
Page 313 and 314: ` Appendix E: Serial Data OutputPos
Page 317 and 318: ` Appendix E: Serial Data OutputDYN
Page 321 and 322: ` Appendix E: Serial Data Output ZZ
Page 323: ` Appendix E: Serial Data OutputNME
Page 326: Appendix F: User Data LogsThe Recen
show all

SkyView System Installation Guide - Dynon Avionics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?