SkyView System Installation Guide - Dynon Avionics

More documents

Recommendations

Info

SV-COM-C25 Installation, Configuration, and TestingPhysical Installation: SV-COM-PANELSV-COM-PANEL DimensionsFigure 96 - SV-COM-PANEL Dimensions16-2 SkyView System Installation Guide - Revision O
Physical InstallationSV-COM-C25 Installation, Configuration, and TestingSV-COM-PANEL – VERTICAL Installation Dimension Quick Overview Panel Cutout: (irregular – see drawing) Bezel Outline: 1.80” W x 3.532” T (45.72 mm W x 89.71 mm T) Note that the SV-COM-PANEL/V is sized such that two units can be stackedto the same height as the height of an SV-D1000 display.SV-COM-PANEL - HORIZONTAL Installation Dimension Quick Overview Panel Cutout: (irregular – see drawing) Bezel Outline: 3.532” W x 1.80” T (89.71 mm W x 45.72 mm T)The figures on the following pages show recommended panel cutouts, mounting hole patterns,and mechanical dimension for the SV-COM-PANEL/V (vertical) and SV-COM-PANEL/H(horizontal). Use these diagrams to plan for the space required by the display.To mount an SV-COM-PANEL, cut the opening in your panel, drill out the mounting holes, installnutplates, and use the included mounting screws to fasten the display to the panel.Your SV-COM-C25 is shipped with #6-32 hex-drive round head fasteners. Fasteners are 5/8”long and require a 5/64” hex drive tool. Dynon recommends fastening the included mountingscrews to nut plates installed behind the panel. If access behind the panel allows, standard #6-32 lock nuts or nuts with lock washers can be used. Do not rivet the SV-COM-PANEL to the panelas this will hinder future removal if necessary.The following installation procedure should be followed to install the SV-COM-425 remotetransceiver module, remembering to allow adequate space for installation of cables andconnectors. If you are installing two COM radios, it is acceptable to co-locate the two SV-COM-425transceiver modules. Select a position in the aircraft for the SV-COM-425 that is not too close to any highexternal heat source. (The SV-COM-425 is not a significant heat source itself and doesnot need to be kept away from other devices for this reason). Avoid sharp bends and placing the cables too near to the aircraft control cables. Secure the SV-COM-425 to the aircraft via the four (4) mounting holes. The unit shouldbe mounted to a flat surface.Additional items you will require for installation of SV-COM-C25, but which are not in the SV-COM-C25 package, include: Nutplates for mounting SV-COM-PANEL to the panel Circuit breaker or fuse for power to SV-COM-425 Power wires to SV-COM-425 SV-COM-425 to SV-COM-PANEL wiring SkyView Network cables to connect the SV-COM-PANEL to SkyView NetworkSkyView System Installation Guide - Revision O 16-3
Page 1:
SkyViewSystem Installation GuideThi
Page 6 and 7:
Revision Revision Date Descriptionh
Page 8 and 9:
Revision Revision Date DescriptionC
Page 11 and 12:
Table of ContentsContact Informatio
Page 13 and 14:
Table of ContentsTachometer .......
Page 15:
Table of Contents19. Appendix C: Wi
Page 18 and 19:
IntroductionAbout this GuideIn the
Page 21 and 22:
2. System PlanningInstallers should
Page 23 and 24:
System PlanningTemperature Specific
Page 25 and 26:
System PlanningIn order to provide
Page 27 and 28:
System Planningferrous material suc
Page 29 and 30:
SV-XPNDR-26XSystem PlanningThe SV-X
Page 31 and 32:
System PlanningSkyView System Const
Page 33 and 34:
System PlanningTest SkyView Network
Page 35 and 36:
System PlanningDynon Part NumberSV-
Page 37 and 38:
System PlanningFigure 8- SkyView Sy
Page 39:
System PlanningSoftware is in use.
Page 42 and 43:
Basic SkyView Display OperationDisp
Page 44 and 45:
Basic SkyView Display OperationA bu
Page 46 and 47:
Basic SkyView Display OperationBasi
Page 48 and 49:
Basic SkyView Display OperationYou
Page 50 and 51:
Basic SkyView Display Operationthis
Page 52 and 53:
Basic SkyView Display OperationFlig
Page 54 and 55:
Basic SkyView Display OperationFirm
Page 57 and 58:
4. SV-D700 / SV-D1000 Installation
Page 59 and 60:
SV-D700 / SV-D1000 Installation and
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Internal Time KeepingSV-D700 / SV-D
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
5. SV-ADAHRS-20X Installation and C
Page 85 and 86:
SV-ADAHRS-20X Installation and Conf
Page 87 and 88:
SV-OAT-340 Location and Installatio
Page 89 and 90:
Measurement UnitsSV-ADAHRS-20X Inst
Page 91 and 92:
Page 93 and 94:
6. SV-MAP-270 Navigation Mapping So
Page 95 and 96:
Page 97:
Page 100 and 101:
SV-EMS-220/221 Installation and Con
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 165 and 166:
8. SV-GPS-250 Installation and Conf
Page 167 and 168:
SV-GPS-250 Installation and Configu
Page 169 and 170:
9. SV-BAT-320 InstallationThis chap
Page 171 and 172:
SV-BAT-320 Installationvoltages to
Page 173:
SV-BAT-320 InstallationTest Procedu
Page 176 and 177:
Autopilot Servo Installation, Confi
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 197 and 198:
11. SV-XPNDR-26X Installation, Conf
Page 199 and 200:
SV-XPNDR-26X Installation, Configur
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208: SV-XPNDR-26X Installation, Configur
Page 215 and 216: Post Installation ChecksSV-XPNDR-26
Page 217 and 218: 12. SV-ARINC-429 Installation and C
Page 219 and 220: SV-ARINC-429 Installation and Confi
Page 221 and 222: ARINC Device ConnectionsSV-ARINC-42
Page 223 and 224: SV-ARINC-429 Installation and Confi
Page 225: SV-ARINC-429 Installation and Confi
Page 228 and 229: Vertical Power VP-X Integration and
Page 230 and 231: Vertical Power VP-X Integration and
Page 233 and 234: 14. SV-ADSB-470 Installation, Confi
Page 235 and 236: SV-ADSB-470 Installation, Configura
Page 241: Post Installation ChecksSV-ADSB-470
Page 244 and 245: Accessory Installation and Configur
Page 260 and 261: SV-COM-C25 Installation, Configurat
Page 274 and 275: Appendix A: Maintenance and Trouble
Page 284 and 285: Appendix B: SpecificationsSkyView E
Page 286 and 287: Appendix B: SpecificationsSV-XPNDR-
Page 288 and 289: Appendix B: SpecificationsSV-COM-C2
Page 290 and 291: Appendix C: Wiring and Electrical C
Page 309 and 310:
20. Appendix D: SV-EMS-220/221 Sens
Page 311 and 312:
21. Appendix E: Serial Data OutputA
Page 313 and 314:
` Appendix E: Serial Data OutputPos
Page 315 and 316:
Page 317 and 318:
` Appendix E: Serial Data OutputDYN
Page 319 and 320:
Page 321 and 322:
` Appendix E: Serial Data Output ZZ
Page 323:
` Appendix E: Serial Data OutputNME
Page 326:
Appendix F: User Data LogsThe Recen
show all

SkyView System Installation Guide - Dynon Avionics

Create successful ePaper yourself

Delete template?

Save as template?