SkyView System Installation Guide - Dynon Avionics

More documents

Recommendations

Info

Accessory Installation and ConfigurationHeater Controller WiringFigure 90–Heated AOA/Pitot Probe Wiring OverviewBefore making the connections to your Heated AOA/Pitot Probe and controller, refer toAppendix C: Wiring and Electrical Connections. The table below provides general15-4 SkyView System Installation Guide - Revision O
Accessory Installation and Configurationrecommendations for wire gauge choice, given wiring run length. It assumes 10 amps ofcurrent.Probe to Controller WiringRun length (in feet) Gauge0 to 7 18 AWG7 to 9 16 AWG10 to 16 14 AWG17 to 24 12 AWG25 to 40 10 AWGTable 48–From FAA AC 43.13-1B, page 11-30As mentioned above, it is preferable that the heater controller box be mounted near enough tothe probe that 5 wires between the controller and probe can be connected without extension.The three mating pairs of colored wires–terminated with Fastons–are used to carry the currentto the heating element in the probe. The 2 white wires are for temperature measurement, andcan be small. If you have mounted the heater controller near the probe and do not need toextend the wires between the two, simply plug each wire on the controller into itscorresponding like-colored wire from the probe.If you do need to extend the wires between the probe and the controller, use therecommended wire size (see Table 48) for your run length. Since extending the wire runsrequires that you cut the connectors off the 5 wires between the probe and controller, splicethe extension wires between the probe and controller using butt splices or other similarlysecure method. The white wires are not polarity-dependent. Additionally, as the white wires donot carry any significant current, you may extend them with 26 AWG or larger for any runlength.Controller Power WiringThree wires–colored red, black, and white–exit the controller for connection to your electricalsystem. Power (between 10 and 15 volts DC) is fed to the controller via the red and black wires.The maximum current draw of the heated pitot controller/probe is 10 amps. You must routeyour own appropriately-sized wires to where the heater controller is mounted. Both power andground lines should be able to handle 10 amps with minimal voltage drop, as recommended inTable 48.The red wire should be connected through a pilot-accessible switch to the main power sourcein the aircraft (limited to 15 volts DC). The switch allows you to manually turn the heatercontroller on and off, depending on the situation. Install a 15 amp fuse at any point along thepower line to the heater controller. Remember that even when the controller is powered on, itonly heats the probe the amount necessary to maintain temperature.The black wire should be permanently connected to ground. Cutting power to the heatercontroller should occur via the red power line, not the black ground line.SkyView System Installation Guide - Revision O 15-5
Page 1:
SkyViewSystem Installation GuideThi
Page 6 and 7:
Revision Revision Date Descriptionh
Page 8 and 9:
Revision Revision Date DescriptionC
Page 11 and 12:
Table of ContentsContact Informatio
Page 13 and 14:
Table of ContentsTachometer .......
Page 15:
Table of Contents19. Appendix C: Wi
Page 18 and 19:
IntroductionAbout this GuideIn the
Page 21 and 22:
2. System PlanningInstallers should
Page 23 and 24:
System PlanningTemperature Specific
Page 25 and 26:
System PlanningIn order to provide
Page 27 and 28:
System Planningferrous material suc
Page 29 and 30:
SV-XPNDR-26XSystem PlanningThe SV-X
Page 31 and 32:
System PlanningSkyView System Const
Page 33 and 34:
System PlanningTest SkyView Network
Page 35 and 36:
System PlanningDynon Part NumberSV-
Page 37 and 38:
System PlanningFigure 8- SkyView Sy
Page 39:
System PlanningSoftware is in use.
Page 42 and 43:
Basic SkyView Display OperationDisp
Page 44 and 45:
Basic SkyView Display OperationA bu
Page 46 and 47:
Basic SkyView Display OperationBasi
Page 48 and 49:
Basic SkyView Display OperationYou
Page 50 and 51:
Basic SkyView Display Operationthis
Page 52 and 53:
Basic SkyView Display OperationFlig
Page 54 and 55:
Basic SkyView Display OperationFirm
Page 57 and 58:
4. SV-D700 / SV-D1000 Installation
Page 59 and 60:
SV-D700 / SV-D1000 Installation and
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Internal Time KeepingSV-D700 / SV-D
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
5. SV-ADAHRS-20X Installation and C
Page 85 and 86:
SV-ADAHRS-20X Installation and Conf
Page 87 and 88:
SV-OAT-340 Location and Installatio
Page 89 and 90:
Measurement UnitsSV-ADAHRS-20X Inst
Page 91 and 92:
Page 93 and 94:
6. SV-MAP-270 Navigation Mapping So
Page 95 and 96:
Page 97:
Page 100 and 101:
SV-EMS-220/221 Installation and Con
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 165 and 166:
8. SV-GPS-250 Installation and Conf
Page 167 and 168:
SV-GPS-250 Installation and Configu
Page 169 and 170:
9. SV-BAT-320 InstallationThis chap
Page 171 and 172:
SV-BAT-320 Installationvoltages to
Page 173:
SV-BAT-320 InstallationTest Procedu
Page 176 and 177:
Autopilot Servo Installation, Confi
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 197 and 198: 11. SV-XPNDR-26X Installation, Conf
Page 199 and 200: SV-XPNDR-26X Installation, Configur
Page 215 and 216: Post Installation ChecksSV-XPNDR-26
Page 217 and 218: 12. SV-ARINC-429 Installation and C
Page 219 and 220: SV-ARINC-429 Installation and Confi
Page 221 and 222: ARINC Device ConnectionsSV-ARINC-42
Page 223 and 224: SV-ARINC-429 Installation and Confi
Page 225: SV-ARINC-429 Installation and Confi
Page 228 and 229: Vertical Power VP-X Integration and
Page 230 and 231: Vertical Power VP-X Integration and
Page 233 and 234: 14. SV-ADSB-470 Installation, Confi
Page 235 and 236: SV-ADSB-470 Installation, Configura
Page 241: Post Installation ChecksSV-ADSB-470
Page 244 and 245: Accessory Installation and Configur
Page 258 and 259: SV-COM-C25 Installation, Configurat
Page 274 and 275: Appendix A: Maintenance and Trouble
Page 284 and 285: Appendix B: SpecificationsSkyView E
Page 286 and 287: Appendix B: SpecificationsSV-XPNDR-
Page 288 and 289: Appendix B: SpecificationsSV-COM-C2
Page 290 and 291: Appendix C: Wiring and Electrical C
Page 296 and 297:
Appendix C: Wiring and Electrical C
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 309 and 310:
20. Appendix D: SV-EMS-220/221 Sens
Page 311 and 312:
21. Appendix E: Serial Data OutputA
Page 313 and 314:
` Appendix E: Serial Data OutputPos
Page 315 and 316:
Page 317 and 318:
` Appendix E: Serial Data OutputDYN
Page 319 and 320:
Page 321 and 322:
` Appendix E: Serial Data Output ZZ
Page 323:
` Appendix E: Serial Data OutputNME
Page 326:
Appendix F: User Data LogsThe Recen
show all

SkyView System Installation Guide - Dynon Avionics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?