SkyView System Installation Guide - Dynon Avionics

More documents

Recommendations

Info

SV-EMS-220/221 Installation and ConfigurationExample Oil Temperature Sensor SetupAssume this sensor was mapped on the Sensor Input Mapping Wizard as:PIN # FUNCTION SENSOR NAMEC37 P7 TEMPERATURE 5/8”-18 NPT FLUID TEMP (100409-000) OILNow, we want to configure its alert and graphical properties. Go to the Sensor Setup Menu andopen the OIL TEMPERATURE Page (SETUP MENU > EMS SETUP > SENSOR SETUP > OILTEMPERATURE).Configure OIL TEMPERATURE with the following properties: ALARM: LATCHING MAXIMUM GRAPHICAL DISPLAY: 260 °F MINIMUM GRAPHICAL DISPLAY: 80 °F RANGE 1o ENABLEYESo COLORYELLOWo TOP 165 °Fo BOTTOM 80 °F RANGE 2o ENABLEYESo COLORGREENo TOP 220 °Fo BOTTOM 165 °F RANGE 3o ENABLEYESo COLORYELLOWo TOP 240 °Fo BOTTOM 220 °F RANGE 4o ENABLEYESo COLORREDo TOP 260 °Fo BOTTOM 240 °F RANGE 5o ENABLENOo COLORREDo TOP 5 °Fo BOTTOM 0 °FFigure 46–Anatomy of aWidget: OilTemperatureNote that oil temperature is configured with a latching alarm in this example. If oiltemperature ever reaches a range configured as red, an alarm will trigger and amessage will show up in the message box on the Main Menu.7-62 SkyView System Installation Guide - Revision O
EMS Screen Layout EditorSV-EMS-220/221 Installation and ConfigurationDynon offers preconfigured Engine Page layouts that support popular enginesensor installations. Check our website at www.dynonavionics.com for moredetails.All sensor mapping, settings, and widget graphical properties are automaticallyshared between displays. Installers do not need to transfer files between displays.Use this wizard to configure the style and layout of the engine and environmental sensorgauges and calculated parameters (e.g., % power) on the 100%, 50%, and 20% Engine Pages.Note that sensors must be defined, mapped, and configured in order to show up on an EnginePage (reference the EMS Sensor Definitions, Mapping, and Settings Section of this guide forinstructions on how to do this).To use this tool, enter the wizard (SETUP MENU > EMS SETUP > SCREEN LAYOUT EDITOR), thenchoose the page size to edit. Once in the Screen Layout Editor, follow this procedure:1. Add a sensor or info widget to the screen. Press either SENSOR or INFO to show theirrespective menus and scroll through available sensors or info parameters, highlight one,and then press ACCEPT or move either joystick to the right to add it to the screen.2. Change the style of the widget. Press STYLE or turn the joystick until the widget’s style isacceptable.3. Change the size of the widget. Press SIZE until the widget’s size is acceptable.4. Change the location of the widget on the screen. Move the CURSR joystick in up, down,right, and left directions until the location is acceptable. Hold the joystick in thosemovement positions for accelerated widget movement.5. Repeat the above steps for all sensors that you want displayed on the Engine Page.6. Save the page by pressing SAVE.Press REMOVE to remove the chosen widget from the screen. Press CANCEL to return to theEMS Setup Menu without saving any changes.Example widget configurationThis example configures an oil temperature widget using the instructions mentioned above.This is the same oil temperature sensor that was configured earlier (see Example OilTemperature Sensor Setup).Open the Screen Layout Editor for the 100% page (SETUP MENU > EMS SETUP > SCREENLAYOUT EDITOR > 100% PAGE…). Now press SENSOR, scroll to the OIL TEMPERATURE sensor,and press ACCEPT. The following widget shows up on the middle on the screen:Figure 47–Oil Temperature WidgetSkyView System Installation Guide - Revision O 7-63
Page 1:
SkyViewSystem Installation GuideThi
Page 6 and 7:
Revision Revision Date Descriptionh
Page 8 and 9:
Revision Revision Date DescriptionC
Page 11 and 12:
Table of ContentsContact Informatio
Page 13 and 14:
Table of ContentsTachometer .......
Page 15:
Table of Contents19. Appendix C: Wi
Page 18 and 19:
IntroductionAbout this GuideIn the
Page 21 and 22:
2. System PlanningInstallers should
Page 23 and 24:
System PlanningTemperature Specific
Page 25 and 26:
System PlanningIn order to provide
Page 27 and 28:
System Planningferrous material suc
Page 29 and 30:
SV-XPNDR-26XSystem PlanningThe SV-X
Page 31 and 32:
System PlanningSkyView System Const
Page 33 and 34:
System PlanningTest SkyView Network
Page 35 and 36:
System PlanningDynon Part NumberSV-
Page 37 and 38:
System PlanningFigure 8- SkyView Sy
Page 39:
System PlanningSoftware is in use.
Page 42 and 43:
Basic SkyView Display OperationDisp
Page 44 and 45:
Basic SkyView Display OperationA bu
Page 46 and 47:
Basic SkyView Display OperationBasi
Page 48 and 49:
Basic SkyView Display OperationYou
Page 50 and 51:
Basic SkyView Display Operationthis
Page 52 and 53:
Basic SkyView Display OperationFlig
Page 54 and 55:
Basic SkyView Display OperationFirm
Page 57 and 58:
4. SV-D700 / SV-D1000 Installation
Page 59 and 60:
SV-D700 / SV-D1000 Installation and
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Internal Time KeepingSV-D700 / SV-D
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
5. SV-ADAHRS-20X Installation and C
Page 85 and 86:
SV-ADAHRS-20X Installation and Conf
Page 87 and 88:
SV-OAT-340 Location and Installatio
Page 89 and 90:
Measurement UnitsSV-ADAHRS-20X Inst
Page 91 and 92:
Page 93 and 94:
6. SV-MAP-270 Navigation Mapping So
Page 95 and 96:
Page 97:
Page 100 and 101:
SV-EMS-220/221 Installation and Con
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111: SV-EMS-220/221 Installation and Con
Page 165 and 166: 8. SV-GPS-250 Installation and Conf
Page 167 and 168: SV-GPS-250 Installation and Configu
Page 169 and 170: 9. SV-BAT-320 InstallationThis chap
Page 171 and 172: SV-BAT-320 Installationvoltages to
Page 173: SV-BAT-320 InstallationTest Procedu
Page 176 and 177: Autopilot Servo Installation, Confi
Page 197 and 198: 11. SV-XPNDR-26X Installation, Conf
Page 199 and 200: SV-XPNDR-26X Installation, Configur
Page 211 and 212:
SV-XPNDR-26X Installation, Configur
Page 213 and 214:
SV-XPNDR-26X Installation, Configur
Page 215 and 216:
Post Installation ChecksSV-XPNDR-26
Page 217 and 218:
12. SV-ARINC-429 Installation and C
Page 219 and 220:
SV-ARINC-429 Installation and Confi
Page 221 and 222:
ARINC Device ConnectionsSV-ARINC-42
Page 223 and 224:
Page 225:
Page 228 and 229:
Vertical Power VP-X Integration and
Page 230 and 231:
Vertical Power VP-X Integration and
Page 233 and 234:
14. SV-ADSB-470 Installation, Confi
Page 235 and 236:
SV-ADSB-470 Installation, Configura
Page 237 and 238:
Page 239 and 240:
Page 241:
Post Installation ChecksSV-ADSB-470
Page 244 and 245:
Accessory Installation and Configur
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
SV-COM-C25 Installation, Configurat
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Appendix A: Maintenance and Trouble
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Appendix B: SpecificationsSkyView E
Page 286 and 287:
Appendix B: SpecificationsSV-XPNDR-
Page 288 and 289:
Appendix B: SpecificationsSV-COM-C2
Page 290 and 291:
Appendix C: Wiring and Electrical C
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 309 and 310:
20. Appendix D: SV-EMS-220/221 Sens
Page 311 and 312:
21. Appendix E: Serial Data OutputA
Page 313 and 314:
` Appendix E: Serial Data OutputPos
Page 315 and 316:
Page 317 and 318:
` Appendix E: Serial Data OutputDYN
Page 319 and 320:
Page 321 and 322:
` Appendix E: Serial Data Output ZZ
Page 323:
` Appendix E: Serial Data OutputNME
Page 326:
Appendix F: User Data LogsThe Recen
show all

SkyView System Installation Guide - Dynon Avionics

Create successful ePaper yourself

Delete template?

Save as template?