SkyView System Installation Guide - Dynon Avionics

More documents

Recommendations

Info

SV-EMS-220/221 Installation and Configurationfull fuel and an optional second “preset” fuel quantity. Once programmed, typical aircraft fuelloads are then quickly recalled under in the EMS > FUEL menu as described in the Pilots UserGuide.There are three fuel computer options, found under SYSTEM SETUP > SYSTEM SETUP >AIRCRAFT INFORMATION. They are only applicable if you have a fuel flow sensor installed:Total Fuel Capacity–set this to the total usable fuel on board when the tanks are full.Once this is set, the pilot is prevented from accidentally setting more than this amountof fuel on board.Preset Fuel Capacity–this can be used to quickly recall a second, non-full starting fuelstate. For example, if your tanks have tabs so that you can easily fill to ¾ of your normalfull fuel load, you would enter this number here so that you can quickly set your fuelcomputer to this second preset when you fill to the tabs.Fuel Added Detect–When set to yes, SkyView will check for discrepancies between thephysical fuel quantity senders and the fuel computer’s calculated fuel load on boot-up.If one is found, SkyView will prompt the user to adjust the fuel computer’s fuel state.This option should only be set to YES on one display if you have more than one in thesystem.Manual EMS Sensor Settings ConfigurationGo to the Sensor Setup Menu (SETUP MENU > EMS SETUP > SENSOR SETUP) to manuallyconfigure the settings of an EMS sensor. Once there, a list of every mapped sensor is displayed.Follow this basic procedure to configure sensor settings:1. Choose a sensor. Scroll through the menu to a sensor and move the joystick right toenter to the sensor configuration menu.2. Set the alarm. Scroll to the ALARM configuration line, move the joystick right to enterthe Alarm Adjust Menu, choose the appropriate alarm for the sensor, and then pressACCEPT. Press BACK to return to the sensor configuration menu.3. Set the graphical display limits. Scroll to the MAXIMUM and MINIMUM GRAPHICALDISPLAY lines, move the joystick right to enter the respective menus, adjust the valuesappropriately - and then press ACCEPT. Press BACK to return to the sensor configurationmenu.4. Set the ranges. Scroll the menu and configure enable, color, and top and bottom.5. Save the settings. Press BACK to return to the Sensor Setup Menu. Press EXIT to returnto the Main Menu.The examples on the following pages show four configured sensors: a voltmeter, a contact,RPM, and an oil temperature sensor.7-58 SkyView System Installation Guide - Revision O
Example Voltmeter SetupSV-EMS-220/221 Installation and ConfigurationAssume this sensor was mapped on the Sensor Input Mapping Wizard as:PIN # FUNCTION SENSOR NAMEC37 P1 VOLTS VOLTAGE MEASURE MAINNow, we want to configure its alert and graphical properties. Go to the Sensor Setup Menu andopen the MAIN VOLTS Page (SETUP MENU > EMS SETUP > SENSOR SETUP > MAIN VOLTS).Configure MAIN VOLTS with the following properties: ALARM: OFF MAXIMUM GRAPHICAL DISPLAY: 15.0 VOLTS MINIMUM GRAPHICAL DISPLAY: 10.0 VOLTS RANGE 1o ENABLEo COLORo TOPo BOTTOM RANGE 2o ENABLEo COLORo TOPo BOTTOM RANGE 3o ENABLEo COLORo TOPo BOTTOM RANGE 4o ENABLEo COLORo TOPo BOTTOM RANGE 5o ENABLEo COLORo TOPo BOTTOMYESRED11.0 VOLTS10.0 VOLTSYESYELLOW12.0 VOLTS11.0 VOLTSYESGREEN13.6 VOLTS12.0 VOLTSYESYELLOW14.6 VOLTS13.6 VOLTSYESRED15.0 VOLTS14.6 VOLTSFigure 43—Anatomy of a Widget:Main VoltsSkyView System Installation Guide - Revision O 7-59
Page 1:
SkyViewSystem Installation GuideThi
Page 6 and 7:
Revision Revision Date Descriptionh
Page 8 and 9:
Revision Revision Date DescriptionC
Page 11 and 12:
Table of ContentsContact Informatio
Page 13 and 14:
Table of ContentsTachometer .......
Page 15:
Table of Contents19. Appendix C: Wi
Page 18 and 19:
IntroductionAbout this GuideIn the
Page 21 and 22:
2. System PlanningInstallers should
Page 23 and 24:
System PlanningTemperature Specific
Page 25 and 26:
System PlanningIn order to provide
Page 27 and 28:
System Planningferrous material suc
Page 29 and 30:
SV-XPNDR-26XSystem PlanningThe SV-X
Page 31 and 32:
System PlanningSkyView System Const
Page 33 and 34:
System PlanningTest SkyView Network
Page 35 and 36:
System PlanningDynon Part NumberSV-
Page 37 and 38:
System PlanningFigure 8- SkyView Sy
Page 39:
System PlanningSoftware is in use.
Page 42 and 43:
Basic SkyView Display OperationDisp
Page 44 and 45:
Basic SkyView Display OperationA bu
Page 46 and 47:
Basic SkyView Display OperationBasi
Page 48 and 49:
Basic SkyView Display OperationYou
Page 50 and 51:
Basic SkyView Display Operationthis
Page 52 and 53:
Basic SkyView Display OperationFlig
Page 54 and 55:
Basic SkyView Display OperationFirm
Page 57 and 58:
4. SV-D700 / SV-D1000 Installation
Page 59 and 60:
SV-D700 / SV-D1000 Installation and
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Internal Time KeepingSV-D700 / SV-D
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
5. SV-ADAHRS-20X Installation and C
Page 85 and 86:
SV-ADAHRS-20X Installation and Conf
Page 87 and 88:
SV-OAT-340 Location and Installatio
Page 89 and 90:
Measurement UnitsSV-ADAHRS-20X Inst
Page 91 and 92:
Page 93 and 94:
6. SV-MAP-270 Navigation Mapping So
Page 95 and 96:
Page 97:
Page 100 and 101:
SV-EMS-220/221 Installation and Con
Page 102 and 103:
Page 104 and 105:
Page 106 and 107: SV-EMS-220/221 Installation and Con
Page 165 and 166: 8. SV-GPS-250 Installation and Conf
Page 167 and 168: SV-GPS-250 Installation and Configu
Page 169 and 170: 9. SV-BAT-320 InstallationThis chap
Page 171 and 172: SV-BAT-320 Installationvoltages to
Page 173: SV-BAT-320 InstallationTest Procedu
Page 176 and 177: Autopilot Servo Installation, Confi
Page 197 and 198: 11. SV-XPNDR-26X Installation, Conf
Page 199 and 200: SV-XPNDR-26X Installation, Configur
Page 207 and 208:
SV-XPNDR-26X Installation, Configur
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Post Installation ChecksSV-XPNDR-26
Page 217 and 218:
12. SV-ARINC-429 Installation and C
Page 219 and 220:
SV-ARINC-429 Installation and Confi
Page 221 and 222:
ARINC Device ConnectionsSV-ARINC-42
Page 223 and 224:
Page 225:
Page 228 and 229:
Vertical Power VP-X Integration and
Page 230 and 231:
Vertical Power VP-X Integration and
Page 233 and 234:
14. SV-ADSB-470 Installation, Confi
Page 235 and 236:
SV-ADSB-470 Installation, Configura
Page 237 and 238:
Page 239 and 240:
Page 241:
Post Installation ChecksSV-ADSB-470
Page 244 and 245:
Accessory Installation and Configur
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
SV-COM-C25 Installation, Configurat
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Appendix A: Maintenance and Trouble
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Appendix B: SpecificationsSkyView E
Page 286 and 287:
Appendix B: SpecificationsSV-XPNDR-
Page 288 and 289:
Appendix B: SpecificationsSV-COM-C2
Page 290 and 291:
Appendix C: Wiring and Electrical C
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 309 and 310:
20. Appendix D: SV-EMS-220/221 Sens
Page 311 and 312:
21. Appendix E: Serial Data OutputA
Page 313 and 314:
` Appendix E: Serial Data OutputPos
Page 315 and 316:
Page 317 and 318:
` Appendix E: Serial Data OutputDYN
Page 319 and 320:
Page 321 and 322:
` Appendix E: Serial Data Output ZZ
Page 323:
` Appendix E: Serial Data OutputNME
Page 326:
Appendix F: User Data LogsThe Recen
show all

SkyView System Installation Guide - Dynon Avionics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?