SkyView System Installation Guide - Dynon Avionics

More documents

Recommendations

Info

SV-EMS-220/221 Installation and ConfigurationConnect the red wire to EMS pin 15 (12V power). Connect the black wire to ground (an SV-EMS-220/221 ground is appropriate). Connect the white wire to any of the “C” type inputs on the SV-EMS-220/221 module - pins 8, 22, or 31 only.Fuel Flow SensorThe approximate pulses/gallon setting for the FloScan 201B (i.e., cast metal caselegacy Dynon sensor) is 28,000 to 31,000. The approximate pulses/gallon for theElectronics International FT-60 (i.e., the red cube) is 68,000. You must configure thefuel flow sensor using this numerical value in the Sensor Setup Menu (SETUP MENU> HARDWARE CALIBRATION > EMS CALIBRATION > FUEL FLOW CALIBRATION).More information on this topic is discussed in the Fuel Computer Configurationsection of this chapter.7-40 SkyView System Installation Guide - Revision O
SV-EMS-220/221 Installation and ConfigurationFloScan 201B sensor only: make note of the numbers on the tag (pulses / gallon)attached to the fuel flow sensor.Dynon Avionics supplies theElectronics International FT-60(Dynon P/N 100403-003) fuel flowtransducer. Dynon no longersupplies the FloScan 201B, butSkyView is compatible with thissensor.The SV-EMS-220/221 supportsdifferential fuel flow sensorinstallations in Rotax 912 and 914installations as illustrated in Figure38.Table 34 revisits which SV-EMS-220/221 pins are compatible withfuel flow sources.General Placement RecommendationsPin13 or 16or 17Fuel FlowSensorWireColorDynonHarnessWire ColorFunctionBlack Black Ground14Yellow orFuel Flow Input 1YellowWhite(From fuel tank)15 Red Red +12 volt AuxiliaryFuel Flow Input 219for optional 2 ndYellow orWhite/Black transducerWhite(Return to fueltank)Table 34–SV-EMS-220/221 Fuel Flow Connections Do not install the Fuel Flow Transducer, hoses and fittings near exhaust system orturbocharger. Excessive heat can damage fuel system components. Do not install 90 degree fittings (elbows) on the input or output of the Fuel FlowTransducer. Doing so will cause turbulence in the fuel flow which causes inaccurate fuelflow data. Install the Fuel Flow Transducer with the three wires pointed UP. Install a fuel filter UPSTREAM of the fuel flow sensor to screen out debris. For best measuring performance, the fuel should travel uphill by one to two inches (25-50 mm) after leaving the fuel flow sender. Placement of the fuel flow sender relative to other items in the fuel system like fuelpumps is left to the builder. It is common to place the sender downstream of anyauxiliary electric boost pumps but upstream of the engine driven fuel pump.Due to vibration issues, never connect the sensor directly to the engine.Do not use Teflon tape when screwing in any of the fittings.SkyView System Installation Guide - Revision O 7-41
Page 1:
SkyViewSystem Installation GuideThi
Page 6 and 7:
Revision Revision Date Descriptionh
Page 8 and 9:
Revision Revision Date DescriptionC
Page 11 and 12:
Table of ContentsContact Informatio
Page 13 and 14:
Table of ContentsTachometer .......
Page 15:
Table of Contents19. Appendix C: Wi
Page 18 and 19:
IntroductionAbout this GuideIn the
Page 21 and 22:
2. System PlanningInstallers should
Page 23 and 24:
System PlanningTemperature Specific
Page 25 and 26:
System PlanningIn order to provide
Page 27 and 28:
System Planningferrous material suc
Page 29 and 30:
SV-XPNDR-26XSystem PlanningThe SV-X
Page 31 and 32:
System PlanningSkyView System Const
Page 33 and 34:
System PlanningTest SkyView Network
Page 35 and 36:
System PlanningDynon Part NumberSV-
Page 37 and 38:
System PlanningFigure 8- SkyView Sy
Page 39:
System PlanningSoftware is in use.
Page 42 and 43:
Basic SkyView Display OperationDisp
Page 44 and 45:
Basic SkyView Display OperationA bu
Page 46 and 47:
Basic SkyView Display OperationBasi
Page 48 and 49:
Basic SkyView Display OperationYou
Page 50 and 51:
Basic SkyView Display Operationthis
Page 52 and 53:
Basic SkyView Display OperationFlig
Page 54 and 55:
Basic SkyView Display OperationFirm
Page 57 and 58:
4. SV-D700 / SV-D1000 Installation
Page 59 and 60:
SV-D700 / SV-D1000 Installation and
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Internal Time KeepingSV-D700 / SV-D
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
5. SV-ADAHRS-20X Installation and C
Page 85 and 86:
SV-ADAHRS-20X Installation and Conf
Page 87 and 88: SV-OAT-340 Location and Installatio
Page 89 and 90: Measurement UnitsSV-ADAHRS-20X Inst
Page 91 and 92: SV-ADAHRS-20X Installation and Conf
Page 93 and 94: 6. SV-MAP-270 Navigation Mapping So
Page 95 and 96: SV-ADAHRS-20X Installation and Conf
Page 97: SV-ADAHRS-20X Installation and Conf
Page 100 and 101: SV-EMS-220/221 Installation and Con
Page 165 and 166: 8. SV-GPS-250 Installation and Conf
Page 167 and 168: SV-GPS-250 Installation and Configu
Page 169 and 170: 9. SV-BAT-320 InstallationThis chap
Page 171 and 172: SV-BAT-320 Installationvoltages to
Page 173: SV-BAT-320 InstallationTest Procedu
Page 176 and 177: Autopilot Servo Installation, Confi
Page 188 and 189:
Autopilot Servo Installation, Confi
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 197 and 198:
11. SV-XPNDR-26X Installation, Conf
Page 199 and 200:
SV-XPNDR-26X Installation, Configur
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Post Installation ChecksSV-XPNDR-26
Page 217 and 218:
12. SV-ARINC-429 Installation and C
Page 219 and 220:
SV-ARINC-429 Installation and Confi
Page 221 and 222:
ARINC Device ConnectionsSV-ARINC-42
Page 223 and 224:
Page 225:
Page 228 and 229:
Vertical Power VP-X Integration and
Page 230 and 231:
Vertical Power VP-X Integration and
Page 233 and 234:
14. SV-ADSB-470 Installation, Confi
Page 235 and 236:
SV-ADSB-470 Installation, Configura
Page 237 and 238:
Page 239 and 240:
Page 241:
Post Installation ChecksSV-ADSB-470
Page 244 and 245:
Accessory Installation and Configur
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
SV-COM-C25 Installation, Configurat
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Appendix A: Maintenance and Trouble
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Appendix B: SpecificationsSkyView E
Page 286 and 287:
Appendix B: SpecificationsSV-XPNDR-
Page 288 and 289:
Appendix B: SpecificationsSV-COM-C2
Page 290 and 291:
Appendix C: Wiring and Electrical C
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 309 and 310:
20. Appendix D: SV-EMS-220/221 Sens
Page 311 and 312:
21. Appendix E: Serial Data OutputA
Page 313 and 314:
` Appendix E: Serial Data OutputPos
Page 315 and 316:
Page 317 and 318:
` Appendix E: Serial Data OutputDYN
Page 319 and 320:
Page 321 and 322:
` Appendix E: Serial Data Output ZZ
Page 323:
` Appendix E: Serial Data OutputNME
Page 326:
Appendix F: User Data LogsThe Recen
show all

SkyView System Installation Guide - Dynon Avionics

Create successful ePaper yourself

Delete template?

Save as template?