JAZZY 1143 Ultra - Pride Mobility Products
JAZZY 1143 Ultra - Pride Mobility Products JAZZY 1143 Ultra - Pride Mobility Products
ar2.4MAXVII. CARE AND MAINTENANCETIRETUBEAXLE KEYNUTSWASHERSREAR RIMHALF35psiDRIVE WHEELNUTDRIVE WHEELWASHERFRONT RIMHALFFigure 27. Drive WheelFigure 28. Drive Wheel DisassembledFollow these easy steps for a quick and safe repair for both pneumatic and solid tires:1. Turn off the power to the controller.2. Set the power chair up on blocks.3. If you are changing a pneumatic tire, completely deflate it before removing the wheel.4. Remove the drive wheel nut and washer from the wheel axle. See figure 27.5. Pull the wheel off the axle.6. Remove the nuts and washers that fasten the two rim halves together. See figure 28.7. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if it is a solid tire.8. Refasten the two rim halves together.9. Slide the wheel back onto the shaft. Make sure that the key is in the axle slot.10. Reinstall the drive wheel nut and washer onto the wheel axle and tighten.11. Inflate the pneumatic tire to 35 psi (2.4 bar).12. Remove the power chair from the blocks.Battery ReplacementA battery wiring diagram is printed on a decal located on the front battery tray. See VI. “Batteries and Charging” forcorrect battery specifications.MANDATORY! Battery posts, terminals, and related accessories contain lead and leadcompounds. Wear goggles and gloves when handling batteries and wash hands afterhandling.WARNING! The batteries in your power chair should only be serviced or replaced by anauthorized Pride Provider or a qualified technician.WARNING! Do not replace batteries when seat is occupied.WARNING! Power chair batteries are heavy. See specifications table. If you are unableto lift that much weight, be sure to get help.To replace the batteries (Power Elevating Seat):1. Turn off the power to the controller.2. Make sure that the power chair is in drive mode. See III. “Your Power Chair.”42 www.pridemobility.com Jazzy 1143 Ultra
VII. CARE AND MAINTENANCEREAR SHROUD FASTENERSREAR SHROUDCENTER SHROUDYELLOW FASTENERBATTERY WIRING DIAGRAM LABELREAR BATTERYFRONT BATTERYFigure 29. Battery InstallationJazzy 1143 Ultra www.pridemobility.com 43
- Page 1 and 2: JAZZY 1143 UltraHow a Power Chair s
- Page 3 and 4: CONTENTSI. INTRODUCTION............
- Page 5 and 6: I. INTRODUCTIONPRIDE OWNERS CLUBAs
- Page 7 and 8: II. SAFETYDo not lift the mobility
- Page 9 and 10: II. SAFETYBattery charger for indoo
- Page 11 and 12: II. SAFETYWeight LimitationsYour po
- Page 13 and 14: II. SAFETYPublic Streets and Roadwa
- Page 15 and 16: II. SAFETYBatteriesIn addition to f
- Page 17 and 18: II. SAFETYWARNING! Pride strongly r
- Page 19 and 20: III. YOUR POWER CHAIRSuspension:Dri
- Page 21 and 22: III. YOUR POWER CHAIRElectrical Com
- Page 23 and 24: III. YOUR POWER CHAIRManual Freewhe
- Page 25 and 26: IV. ASSEMBLYSEAT INSTALLATIONIt may
- Page 27 and 28: V. COMFORT ADJUSTMENTS12. Reinstall
- Page 29 and 30: V. COMFORT ADJUSTMENTSFoot Platform
- Page 31 and 32: V. COMFORT ADJUSTMENTSElevating Leg
- Page 33 and 34: V. COMFORT ADJUSTMENTSMANDATORY! Re
- Page 35 and 36: VI. BATTERIES AND CHARGINGBATTERIES
- Page 37 and 38: VI. BATTERIES AND CHARGINGFrequentl
- Page 39 and 40: VII. CARE AND MAINTENANCECARE AND M
- Page 41: VII. CARE AND MAINTENANCEStorageYou
- Page 45 and 46: VII. CARE AND MAINTENANCECorrective
- Page 47 and 48: VIII. WARRANTYRECONDITIONED UNITS W
- Page 49 and 50: NOTESJazzy 1143 Ultra www.pridemobi
- Page 51: Quality Control - Jazzy 1143 UltraI
ar2.4MAXVII. CARE AND MAINTENANCETIRETUBEAXLE KEYNUTSWASHERSREAR RIMHALF35psiDRIVE WHEELNUTDRIVE WHEELWASHERFRONT RIMHALFFigure 27. Drive WheelFigure 28. Drive Wheel DisassembledFollow these easy steps for a quick and safe repair for both pneumatic and solid tires:1. Turn off the power to the controller.2. Set the power chair up on blocks.3. If you are changing a pneumatic tire, completely deflate it before removing the wheel.4. Remove the drive wheel nut and washer from the wheel axle. See figure 27.5. Pull the wheel off the axle.6. Remove the nuts and washers that fasten the two rim halves together. See figure 28.7. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if it is a solid tire.8. Refasten the two rim halves together.9. Slide the wheel back onto the shaft. Make sure that the key is in the axle slot.10. Reinstall the drive wheel nut and washer onto the wheel axle and tighten.11. Inflate the pneumatic tire to 35 psi (2.4 bar).12. Remove the power chair from the blocks.Battery ReplacementA battery wiring diagram is printed on a decal located on the front battery tray. See VI. “Batteries and Charging” forcorrect battery specifications.MANDATORY! Battery posts, terminals, and related accessories contain lead and leadcompounds. Wear goggles and gloves when handling batteries and wash hands afterhandling.WARNING! The batteries in your power chair should only be serviced or replaced by anauthorized <strong>Pride</strong> Provider or a qualified technician.WARNING! Do not replace batteries when seat is occupied.WARNING! Power chair batteries are heavy. See specifications table. If you are unableto lift that much weight, be sure to get help.To replace the batteries (Power Elevating Seat):1. Turn off the power to the controller.2. Make sure that the power chair is in drive mode. See III. “Your Power Chair.”42 www.pridemobility.com Jazzy <strong>1143</strong> <strong>Ultra</strong>