Modular electrical linear drives OSP-E - parker-origa.com

More documents

Recommendations

Info

Modular electrical linear drives OSP-E8.2.4 OSP-E..SBRLinear drive with ball screw drive, internal plain bearing guide and piston rodDesign Features• Ball screw spindle• Piston rod made of stainless steelDrive shaftSupporting ringswith low frictionDrive shaftBall screw spindleOuter band made ofstainless steelStainless steelpiston rodTwo-row slantedball bearingPermanent magnet forposition detectionBall screw nutSlotted aluminium profile withintegrated dovetail groovesPiston rod thread toISO 6431 or 155528.2.5 OSP-E..STRLinear drive with trapezoidal screw drive, internal plain bearing guide and piston rodDesign Features• Trapezoidal thread drive• Piston rod made of stainless steelDrive shaftPermanent magnet forposition detectionPlastic nutOuter band made of stainlesssteelPiston rod made ofstainless steelTwo-row slantedball bearingSupport rings withlow frictionTrapezoidalthreadedspindleSlotted aluminium profile withintegrated dovetail groovesPiston rod thread accordingto ISO 6431, or1555228
EN8.3 Maintenance / repairAttentionMaintenance and repair work shall only be carried out by specially trained and instructed persons !The machine or the working zone must be cordoned off for safety purposes as required !8.3.1 CleaningThe linear drive must be kept free from dirt particles at all times, particularly the surface between the outerband and the aluminium profile and/or the wipers at the carrier.For cleaning, use only non aggressive cleansers and lint-free cloths.AttentionAfter every cleaning operation, the corresponding parts must be lubricated as required.8.3.2 LubricationThe shaft bearings have life-long lubrication.The following aspects of the linear drives must be taken into account:• Load• Speed• Temperature• Surrounding conditionLubricant for trapezoidal and ball screw spindle as well as cylinder tube• Parker-Origa-grease 2 (HO-Grease 2 Ident N o .: #15071 Tube 45 gr)Inspection interval for linear drive OSP-E..SB and OSP-E..SBRCarry out a visual inspection after an operating period of max. 3000 km or 12 months.Inspection interval for linear drive OSP-E..ST and OSP-E..STRCarry out a visual inspection after an operating period of max. 300 km or 24 months.Visual inspection for lubricating grease• Make sure that the outer band/piston rod has always a thin lubricating film on both sides.• Make sure that the spindles are covered with a thin lubricating film. For this purpose, the clampingpieces for the outer band must be loosened so that this can be lifted up easily.Lubricating the drive OSP-E..SB and OSP-E..ST• Push the carrier (1) into the central position.• Loosen clamping pieces (2) and lift up the outer band (3).• Place a line of grease on the threaded spindle and the inside of the tube.• Push the driver backward and forward a few times by hand to over the entire guide length.• Tightly clamp the outer band again.Thread sizeM 3M 4Tightening torquescountersunk screws0,5 ± 0,1 Nm2,2 ± 0,1 Nm29
Page 1 and 2: Modular electricallinear drives OSP
Page 3 and 4: ENContent1 Foreword to the Operatin
Page 5 and 6: EN2 SafetyOrder No.:Delivery dateCu
Page 7 and 8: EN4.2 Interim storageWhere interim
Page 9 and 10: EN7.1.3 OSP-E..BHDBHD: Linear drive
Page 11 and 12: EN7.1.5 OSP-E..BLinear drive with t
Page 13 and 14: EN7.2.3 OSP-E..BVVertical Linear dr
Page 15 and 16: EN7.3 Maintenance / repairAttention
Page 17 and 18: EN7.3.4 Tensioning the beltOSP-E..B
Page 19 and 20: ENImportant:applies only for OSP-E.
Page 21 and 22: ENOSP-E..BLinear drive with toothed
Page 23 and 24: EN• Tension the belt (8) in accor
Page 25 and 26: EN8.1.2 OSP-E..SBLinear drive with
Page 27: EN8.2 Structural arrangement and op
Page 31 and 32: ENOSP-E..STLinear drive with trapez
Page 33 and 34: EN8.3.5 Replacing the wiper / outer
Page 35 and 36: EN• Place location ring (3) into
Page 37 and 38: EN9.5 Synchronous belt drive with c
Page 39 and 40: EN10 Manufacturer’s statementPark
Page 41 and 42: ENPos. Description Pos. Description
Page 43 and 44: ENPos.DescriptionPos.Description1 C
Page 45 and 46: ENPos. Description1 Cylinder barrel
Page 51 and 52: ENPos.DescriptionPos.Description1 C
Page 53 and 54: ENPos. Description1 CYLINDER BARREL
Page 55 and 56: EN11.9 OSP-E..STRLinear drive with

Modular electrical linear drives OSP-E - parker-origa.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?