Modular electrical linear drives OSP-E - parker-origa.com

More documents

Recommendations

Info

Modular electrical linear drives OSP-E7.2.4 OSP-E..BLinear drive with toothed belt and internal plain bearing guideDesign Features• Toothed belt drive for linear movements• Toothed belt drive with threaded holes for lateral motor attachmentThreaded holes forsecuringBelt wheelSupporting rings withlow frictionDriverCarrierThreaded holesOuter band made ofstainless steelToothed beltwith steel reinforcementSetting belt tensionThreaded holes formotor attachment (ontwo sides)Ball bearingPinionPermanent magnet forposition detectionSlotted aluminium profilewith integrated dovetailgroovesNipple for maintenancelubricationOSP-E..B Bi-Parting versionDesign Features• Drive for synchronous counter movements• Belt drive with threaded holes for lateral motor attachmentSupporting ringsThreaded holes for with low frictionsecuringBelt wheelCarrierThreadedholesToothed beltOuter band made ofstainless steelDriverCarrierSetting belt tensionThreaded holes for motor attachment(on two sides)PinionBall bearingPermanent magnet forposition detectionSlotted aluminium profile with integrateddovetail groovesNipple for maintenancelubrication14
EN7.3 Maintenance / repairAttentionMaintenance and repair work shall only be carried out by specially trained and instructed persons !AttentionThe machine or the working zone must be cordoned off for safety purposes as required !7.3.1 CleaningThe linear drive must be kept free from dirt particles at all times, particularly the surface between the outerband and the aluminium profile and/or the wipers at the carrier.For cleaning, use only non aggressive cleansers and lint-free cloths.AttentionAfter every cleaning operation, the corresponding parts must be lubricated as required.7.3.2 LubricationThe roller guides and shaft bearings are lubricated for life.We recommend an inspection of the linear drive after max. 3000 km or an operating period of 12 months,depending on the application.The following aspects must be taken into account:• Load• Speed• Temperature• Surrounding conditionof the linear drives.Visual inspection for lubricating grease:• Make sure that the outer band has a thin lubricating film on both sides.• Make sure that the guide rail (OSP-E..BHD) is covered with a thin lubricating film as required. For thispurpose, the clamping pieces for the outer band must be loosened so that this can be lifted up easily.Lubrication of the running surfaces in the tube (OSP-E..B):On the downward facing side of the linear drive, there are two grease nipples for lubricating the runningsurfaces. In order to perform lubrication with a grease gun, the driver must be moved into its corres-pondinggreasing position (if necessary, inching movement in the direction of the mechanical limit position of thedrive).Refer to the table for the clearance values.(Drive side)aType Dimension a [mm] Dimension b [mm]OSP-E25B 64 71OSP-E32B 73 79Lubricating nipple(Reverse guide side )bOSP-E50B 98 103Lubricant• Parker-Origa-grease 2(HO-Grease 2 Ident N o .: #15071 Tube 45 gr)Lubricating nipple15
Page 1 and 2: Modular electricallinear drives OSP
Page 3 and 4: ENContent1 Foreword to the Operatin
Page 5 and 6: EN2 SafetyOrder No.:Delivery dateCu
Page 7 and 8: EN4.2 Interim storageWhere interim
Page 9 and 10: EN7.1.3 OSP-E..BHDBHD: Linear drive
Page 11 and 12: EN7.1.5 OSP-E..BLinear drive with t
Page 13: EN7.2.3 OSP-E..BVVertical Linear dr
Page 17 and 18: EN7.3.4 Tensioning the beltOSP-E..B
Page 19 and 20: ENImportant:applies only for OSP-E.
Page 21 and 22: ENOSP-E..BLinear drive with toothed
Page 23 and 24: EN• Tension the belt (8) in accor
Page 25 and 26: EN8.1.2 OSP-E..SBLinear drive with
Page 27 and 28: EN8.2 Structural arrangement and op
Page 29 and 30: EN8.3 Maintenance / repairAttention
Page 31 and 32: ENOSP-E..STLinear drive with trapez
Page 33 and 34: EN8.3.5 Replacing the wiper / outer
Page 35 and 36: EN• Place location ring (3) into
Page 37 and 38: EN9.5 Synchronous belt drive with c
Page 39 and 40: EN10 Manufacturer’s statementPark
Page 41 and 42: ENPos. Description Pos. Description
Page 43 and 44: ENPos.DescriptionPos.Description1 C
Page 45 and 46: ENPos. Description1 Cylinder barrel
Page 51 and 52: ENPos.DescriptionPos.Description1 C
Page 53 and 54: ENPos. Description1 CYLINDER BARREL
Page 55 and 56: EN11.9 OSP-E..STRLinear drive with

Modular electrical linear drives OSP-E - parker-origa.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?