Style 232 Restrained Flexible Coupling For Carbon Steel ... - Victaulic
Style 232 Restrained Flexible Coupling For Carbon Steel ... - Victaulic
Style 232 Restrained Flexible Coupling For Carbon Steel ... - Victaulic
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
RESTRAINED COUPLING<strong>Style</strong> <strong>232</strong> <strong>Restrained</strong> <strong>Flexible</strong> <strong>Coupling</strong>60.05PERFORMANCENominalPipeSizeIn./mm661650721800781950842100902250MaximumWorkingPressurepsi/kPa<strong>Carbon</strong> <strong>Steel</strong>(1) (2) (3) (3) (4) (5)MaximumWorkingPressurepsi/kPaStainless <strong>Steel</strong>MaximumWorkingPressurepsi/kPaDuctile IronPipe EndSeparationMin - MaxIn./mm0.63 - 1.00Max. Allow. Max. PermissibleStatic DeflectionDegreesEnd Loadlbf/N0° 37'342119Body Type100 100 75690 690 515 2 16.0 - 25.4 1521823150 125 1000.63 - 1.0020° 37'5131791035 860 690 16.0 - 25.4 2282735200 200 1500.63 - 1.0020° 37'6842391375 1375 1035 16.0 - 25.4 3043646250 250 2000.75 - 1.0030° 24'8552991725 1725 1375 19.1 - 25.4 3804558350 250 2000.75 - 1.0030° 24'11974182410 1725 1375 19.1 - 25.4 5326381100 75 750.63 - 1.0020° 30'407150690 515 515 16.0 - 25.4 1811095150 125 1000.63 - 1.0020° 30'6107261035 860 690 16.0 - 25.4 2716643200 175 1500.63 - 1.0020° 30'8143011375 1200 1035 16.0 - 25.4 3622191250 250 2000.75 - 1.0030° 22'10178761725 1725 1375 19.1 - 25.4 4527739350 250 2000.75 - 1.0030° 22'14250262410 1725 1375 19.1 - 25.4 6338834100 75 500.63 - 1.0020° 34'477836690 515 345 16.0 - 25.4 2125522150 100 750.63 - 1.0020° 34'7167541035 690 515 16.0 - 25.4 3188283175 150 1250.63 - 1.0020° 34'8362131200 1035 860 16.0 - 25.4 3719663200 200 1750.75 - 1.0030° 22'9556721375 1375 1200 19.1 - 25.4 4251043300 200 1750.75 - 1.0030° 22'14335092065 1375 1200 19.1 - 25.4 6376565100 75 500.63 - 1.0020° 29'554177690 515 345 16.0 - 25.4 2465102150 100 750.63 - 1.0020° 29'8312651035 690 515 16.0 - 25.4 3697653175 150 1250.63 - 1.0020° 29'9698101200 1035 860 16.0 - 25.4 4313929200 200 1500.75 - 1.0030° 19'11083541375 1375 1035 19.1 - 25.4 4930204300 200 1500.75 - 1.0030° 19'16625312065 1375 1035 19.1 - 25.4 7395306100 75 500.63 - 1.0020° 27'636173690 515 345 16.0 - 25.4 2829837125 100 750.63 - 1.0020° 27'795216860 690 5115 16.0 - 25.4 3537296150 150 1000.63 - 1.0020° 27'9542591035 1035 690 16.0 - 25.4 4244755200 200 1500.75 - 1.0030° 18'12723451375 1375 1035 19.1 - 25.4 5659673250 200 1500.75 - 1.0030° 18'15904311725 1375 1035 19.1 - 25.4 7074591(1) <strong>For</strong> allowable test or transient pressure, the maximum working pressure may be increased to 1 1/2 times the value shown.(2) Pipe end separations shown in the table assume the pipe is in a non-deflected state. Maximum allowable axial pipe movement at the joint is thedifference between the maximum and minimum pipe separation. At maximum pipe end separation, axial movement can only occur via pipeexpansion into the joint and vice versa.(3) Pipe end movement and deflection are non-concurrent.(4) Published static deflection values are intended for installation only. <strong>For</strong> allowable in-service or dynamic deflection, use 1/2 of the published staticvalues. The coupling closure should be located 90 degrees from the direction of joint deflection.(5) The maximum permissible end loads listed in the table are calculated using the nominal pipe O.D. The actual maximum permissible end loadwill be less or greater than the published figures depending on the actual pipe O.D.www.victaulic.comVICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2013 VICTAULIC COMPANY. ALL RIGHTS RESERVED.60.05_12REV_M
Change language