Style 232 Restrained Flexible Coupling For Carbon Steel ... - Victaulic

RESTRAINED COUPLINGStyle 232 Restrained Flexible Coupling60.05PERFORMANCENominalPipeDiameterIn./mm820010250123001435016400184502050024600MaximumWorkingPressurepsi/kPaCarbon Steel(1) (2) (3) (3) (4) (5)MaximumWorkingPressurepsi/kPaStainless SteelMaximumWorkingPressurepsi/kPaDuctile IronPipe EndSeparationMin - MaxIn./mm0.38 - 0.75Max.Allow. StaticDeflectionDegreesMax.PermissibleEnd Loadlbf/N10053Body Type200 200 20014° 0'1375 1375 1375 9.7 - 19.1 44718300 300 3000.38 - 0.7524° 0'150802065 2065 2065 9.7 - 19.1 67078200 200 2000.38 - 0.7513° 30'157081375 1375 1375 9.7 - 19.1 69873300 300 3000.38 - 0.7523° 30'235622065 2065 2065 9.7 - 19.1 104809150 150 1500.38 - 0.7513° 15'169651035 1035 1035 9.7 - 19.1 75462300 300 2500.38 - 0.7523° 15'339292065 2065 1725 9.7 - 19.1 150935100 100 1000.38 - 0.7513° 0'15394690 690 690 9.7 - 19.1 68475300 300 2500.38 - 0.7523° 0'461812065 2065 1725 9.7 - 19.1 20542575 75 750.38 - 0.7512° 30'15080515 515 515 9.7 - 19.1 67078200 200 2000.38 - 0.7522° 30'402121375 1375 1375 9.7 - 19.1 178874300 300 3000.63 - 1.0022° 30'603192065 2065 2065 16.0 - 25.4 26831050 50 500.38 - 0.7512° 15'12723345 345 345 9.7 - 19.1 56597200 200 1750.38 - 0.7522° 15'508941375 1375 1200 9.7 - 19.1 226387300 300 2500.63 - 1.0022° 15'763412065 2065 1725 16.0 - 25.4 33958025 25 250.38 - 0.7512° 0'7854170 170 170 9.7 - 19.1 34936200 200 1500.38 - 0.7522° 0'628321375 1375 1035 9.7 - 19.1 279490300 300 2500.63 - 1.0022° 0'942482065 2065 1725 16.0 - 25.4 41923525 25 250.38 - 0.7511° 45'11310170 170 170 9.7 - 19.1 50308150 150 1250.38 - 0.7521° 45'678581035 1035 860 9.7 - 19.1 301849250 250 2000.63 - 1.0021° 45'1130971725 1725 1375 16.0 - 25.4 503082300 250 2000.63 - 1.0021° 45'1357172065 1725 1375 16.0 - 25.4 603398(1) For allowable test or transient pressure, the maximum working pressure may be increased to 1 1/2 times the value shown.(2) Pipe end separations shown in the table assume the pipe is in a non-deflected state. Maximum allowable axial pipe movement at the joint is thedifference between the maximum and minimum pipe separation. At maximum pipe end separation, axial movement can only occur via pipeexpansion into the joint and vice versa.(3) Pipe end movement and deflection are non-concurrent.(4) Published static deflection values are intended for installation only. For allowable in-service or dynamic deflection, use 1/2 of the published staticvalues. The coupling closure should be located 90 degrees from the direction of joint deflection.(5) The maximum permissible end loads listed in the table are calculated using the nominal pipe O.D. The actual maximum permissible end loadwill be less or greater than the published figures depending on the actual pipe O.D.www.victaulic.comVICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2013 VICTAULIC COMPANY. ALL RIGHTS RESERVED.60.05_10REV_M