Catalog: Wood Construction Connectors (C-2009) - Rbb.lv

Fasteners &Quik Drive ® SystemsFasteners & Quik Drive ® SystemsNAIL TYPESNail Types and SizesSpecified for SimpsonStrong-Tie ® connectors016dCommon16dSinker10dCommon8d16dx2¹⁄₂" Common N54A 10dx1¹⁄₂" 8dx1¹⁄₂"Many Simpson Strong-Tie connectorshave been designed and tested for usewith specific types and sizes of nails.The specified quantity, type and sizeof nail must be installed in the correctholes on the connector to achievepublished loads. Other factors suchas nail material and finish are alsoimportant. Incorrect fastener selectionor installation can compromiseconnector performance and couldlead to failure.Simpson Strong-Tie does not offerall of these nails, see page 17 formore information.1¹⁄₂0.148" 0.131"2¹⁄₂30.162" 0.131"0.25"3¹⁄₄3¹⁄₂0.162"0.148"0.148"Nails are drawn to scaleNail diameter assumes no coating.See technical bulletin T-NAILGUIDE formore information. (See page 191)NAIL DESIGN INFORMATIONIn some cases it is desirable to install Simpson Strong-Tie face mount joist hangers and straight straps with nails that are a different type or sizethan what is called out in the load table. In these cases these reduction factors must be applied to the allowable loads listed for the connector.Load Adjustment Factors for Optional NailsUsed with Face Mount Hangers and Straight StrapsCatalog NailReplacementAllowable Load Adjustment FactorFace Mount Hangers Straight Straps16d common (0.162"x3¹⁄₂") 10dx1¹⁄₂ (0.148"x1¹⁄₂") 0.64 0.84 716d common (0.162"x3¹⁄₂")10d common (0.148"x3")12d common (0.148"x3¹⁄₄")0.84 0.8416d common (0.162"x3¹⁄₂") 16d sinker (0.148"x3¹⁄₄") 0.84 0.8416d common (0.162"x3¹⁄₂") 16dx2¹⁄₂ (N16) (0.162"x2¹⁄₂") 1.00 1.0010d common (0.148"x3")12d common (0.148"x3¹⁄₄")16d sinker (0.148"x3¹⁄₄")10dx1¹⁄₂ (0.148"x1¹⁄₂") 0.77 1.00 810d common (0.148"x3")16d sinker (0.148"x3¹⁄₄")10dx1¹⁄₄ (0.148"x1¹⁄₄") 0.64 1.00 810d common (0.148"x3")12d common (0.148"x3¹⁄₄")16d sinker (0.148"x3¹⁄₄") 1.00 1.008d common (0.131"x2¹⁄₂") 8dx1¹⁄₂ (0.131"x1¹⁄₂") 0.85 1.0010d common (0.148"x3") 8d common (0.131"x2¹⁄₂") 0.83 0.83Double shear nailingshould use full lengthcommon nailsC-2009 © 2008 SIMPSON STRONG-TIE COMPANY INC. PRINTED 12/08161. Allowable load adjustment factors shown in the table are based on calculated reduction factors and are applicable forall face mount hangers and straight straps throughout this catalog, except as noted in the footnotes below.2. Some products have been tested specifically with alternate fasteners and have allowable load adjustment factors orreduced capacities published on the specific product page which may differ from the values calculated using this table.3. This table does not apply to hangers modified per the Hanger Options described on pages 181-183, or steel thicker than 10 gauge.4. Unless noted otherwise, 10dx1¹⁄₂" or 16dx2¹⁄₂" nails may not be substituted for joist nails in double-shear hangers(i.e. LUS, MUS, HUS, HHUS, HGUS). For applications involving pneumatic nails, refer to specific tool manufacturertechnical bulletins. Refer to technical bulletin T-PNEUMATIC (see page 191 for details).5. Do not substitute 10dx1¹⁄₂" nails for face nails on slope and skew combinations or skewed only LSU and LSSU.6. For straps installed over sheathing use a 2¹⁄₂" long nail minimum.7. Where noted, use 0.80 for 10 ga, 11 ga, and 12 ga products when using SPF lumber.8. Where noted, use 0.92 for 10 ga, 11 ga, and 12 ga products when using SPF lumber.Shorter nailsmay not be used asdouble shear nails