warp/m service manual - ADB Lighting Technologies
warp/m service manual - ADB Lighting Technologies warp/m service manual - ADB Lighting Technologies
WARP HeadWARP Head8.5 Replace the Back Lens on 12°-30° WARPRequired Tool(s) Spare Part Code Preliminary readingFlat Screw DriverScrew Driver PZ21001.61.300 Chapter 8.121. Unplug the WARP2. Open the two lenses cover3. Remove the Diaphragm (see chapter 8.13)4. Put Front and back lenses at Full5. Remove the 3 taptite screws from the Lens plate6. Remove the 3 Isolations and the ADB Clip7. Change the Lens1001.61.300 includes:• Back Lens 22°-50°• 3 New screws• 3 Isolations• 3 ADB Clip.Service Manual - page 84Issue 0.9www.adblighting.com
WARP Head8.6 Replace the Front Lens on 12°-30° WARPRequired Tool(s) Spare Part Code Preliminary readingFlat Screw DriverScrew Driver PZ21001.61.310 Chapter 8.121. Unplug the WARP2. Open the two lenses cover and remove the diaphragm (see chapter 8.13)3. Put Front and back lenses at 04. Remove the 9 Taptite Screws and the front lens plate5. Remove the 2 screws and the 2 spacers6. Remove the 4 isolations and Clips7. Change the Lens1001.61.310 includes:• Front Lens 12°-30°• 10 New screws for Lens plate• 4 Isolations• 4 ADB Clip• 2 Screwswww.adblighting.com Service Manual - page 85Issue 0.9
- Page 36 and 37: Technical DescriptionFunctions:This
- Page 38 and 39: Technical DescriptionFunctions:This
- Page 40 and 41: Motorised Yoke7 Motorised Yoke - Ma
- Page 42 and 43: Motorised Yoke7.3 Open Motor WingRe
- Page 44 and 45: Motorised Yoke7.5 Replace Front Pan
- Page 46 and 47: Motorised Yoke7.7 Change Motor Boar
- Page 48 and 49: Motorised Yoke7.9 Replace PCB Shutt
- Page 50 and 51: Motorised Yoke7.11 Replace Top Box
- Page 52 and 53: Motorised Yoke7.13 Replace Coarse P
- Page 54 and 55: Motorised Yoke7.15 Replace Coarse T
- Page 56 and 57: Motorised Yoke7.17 Remove WARP from
- Page 58 and 59: Motorised Yoke7.19 Replace Tilt MOT
- Page 60 and 61: Motorised Yoke7.21 Remove Coarse TI
- Page 62 and 63: Motorised Yoke7.22.2 How to install
- Page 64 and 65: Motorised Yoke7.22.2.2 Left Motor W
- Page 66 and 67: Motorised Yoke7.24 Remove Yoke from
- Page 68 and 69: Motorised Yoke7.25 Replace Pan Belt
- Page 70 and 71: Motorised Yoke7.27 IR Sensor Settin
- Page 72 and 73: Motorised Yoke7.28 Motor WingRequir
- Page 74 and 75: Motorised Yoke7.30 Adjust Motors in
- Page 76 and 77: Motorised Yoke8.1.2 How to place th
- Page 78 and 79: Motorised Yoke8.3 Replace the Refle
- Page 80 and 81: Motorised Yoke8.4.2 How replace the
- Page 82 and 83: WARP HeadWARP Head8.4.2.2 Introduce
- Page 84 and 85: WARP HeadWARP HeadPlace all graduat
- Page 88 and 89: WARP HeadWARP Head8.7 Replace the B
- Page 90 and 91: WARP HeadWARP Head8.9 Change Gears
- Page 92 and 93: WARP HeadWARP Head8.11 Remove / Cha
- Page 94 and 95: WARP HeadWARP Head8.13 Replace Diap
- Page 96: WARP HeadWARP HeadService Manual -
WARP Head8.6 Replace the Front Lens on 12°-30° WARPRequired Tool(s) Spare Part Code Preliminary readingFlat Screw DriverScrew Driver PZ21001.61.310 Chapter 8.121. Unplug the WARP2. Open the two lenses cover and remove the diaphragm (see chapter 8.13)3. Put Front and back lenses at 04. Remove the 9 Taptite Screws and the front lens plate5. Remove the 2 screws and the 2 spacers6. Remove the 4 isolations and Clips7. Change the Lens1001.61.310 includes:• Front Lens 12°-30°• 10 New screws for Lens plate• 4 Isolations• 4 <strong>ADB</strong> Clip• 2 Screwswww.adblighting.com Service Manual - page 85Issue 0.9