warp/m service manual - ADB Lighting Technologies
warp/m service manual - ADB Lighting Technologies warp/m service manual - ADB Lighting Technologies
Motorised Yoke8.4.2 How replace the Ring Compartment on a Motorized WARP 12°-30°8.4.2.1 Prepare Rings position for WARP/M 12°-30°Before replace ring compartment, you have to prepare the ring position as describe:Place the ring compartment to see pressed slider of the ring spacer on your right.BACKLEFT SIDERIGHT SIDE:You must seepressed sliderFRONTService Manual - page 78Issue 0.9www.adblighting.com
Motorised YokePlace all graduated wheels as describe:LEFT SIDE FRONT RIGHT SIDEACaution:Rings Positions are different betweenWARP/M 12°-30° and WARP/M 22°-50°BRINGSHUTTERSACCESSORIESFOCALZOOMPOSITIONYou must see all white index, all shutters rings at ZEROYou must see all white index, all accessories rings at ZEROYou must place the ring at Position G + 1.5 and you must seethe white index on your right front of you (detail A)You must place the ring between 11 and 12 and you mustsee the white on back side (detail B)www.adblighting.com Service Manual - page 79Issue 0.9
- Page 30 and 31: Technical Description6.3.2 Pan & Ti
- Page 32 and 33: Technical Description6.3.8 Descript
- Page 34 and 35: Technical Description6.4 Wheels dri
- Page 36 and 37: Technical DescriptionFunctions:This
- Page 38 and 39: Technical DescriptionFunctions:This
- Page 40 and 41: Motorised Yoke7 Motorised Yoke - Ma
- Page 42 and 43: Motorised Yoke7.3 Open Motor WingRe
- Page 44 and 45: Motorised Yoke7.5 Replace Front Pan
- Page 46 and 47: Motorised Yoke7.7 Change Motor Boar
- Page 48 and 49: Motorised Yoke7.9 Replace PCB Shutt
- Page 50 and 51: Motorised Yoke7.11 Replace Top Box
- Page 52 and 53: Motorised Yoke7.13 Replace Coarse P
- Page 54 and 55: Motorised Yoke7.15 Replace Coarse T
- Page 56 and 57: Motorised Yoke7.17 Remove WARP from
- Page 58 and 59: Motorised Yoke7.19 Replace Tilt MOT
- Page 60 and 61: Motorised Yoke7.21 Remove Coarse TI
- Page 62 and 63: Motorised Yoke7.22.2 How to install
- Page 64 and 65: Motorised Yoke7.22.2.2 Left Motor W
- Page 66 and 67: Motorised Yoke7.24 Remove Yoke from
- Page 68 and 69: Motorised Yoke7.25 Replace Pan Belt
- Page 70 and 71: Motorised Yoke7.27 IR Sensor Settin
- Page 72 and 73: Motorised Yoke7.28 Motor WingRequir
- Page 74 and 75: Motorised Yoke7.30 Adjust Motors in
- Page 76 and 77: Motorised Yoke8.1.2 How to place th
- Page 78 and 79: Motorised Yoke8.3 Replace the Refle
- Page 82 and 83: WARP HeadWARP Head8.4.2.2 Introduce
- Page 84 and 85: WARP HeadWARP HeadPlace all graduat
- Page 86 and 87: WARP HeadWARP Head8.5 Replace the B
- Page 88 and 89: WARP HeadWARP Head8.7 Replace the B
- Page 90 and 91: WARP HeadWARP Head8.9 Change Gears
- Page 92 and 93: WARP HeadWARP Head8.11 Remove / Cha
- Page 94 and 95: WARP HeadWARP Head8.13 Replace Diap
- Page 96: WARP HeadWARP HeadService Manual -
Motorised YokePlace all graduated wheels as describe:LEFT SIDE FRONT RIGHT SIDEACaution:Rings Positions are different betweenWARP/M 12°-30° and WARP/M 22°-50°BRINGSHUTTERSACCESSORIESFOCALZOOMPOSITIONYou must see all white index, all shutters rings at ZEROYou must see all white index, all accessories rings at ZEROYou must place the ring at Position G + 1.5 and you must seethe white index on your right front of you (detail A)You must place the ring between 11 and 12 and you mustsee the white on back side (detail B)www.adblighting.com Service Manual - page 79Issue 0.9