warp/m service manual - ADB Lighting Technologies

More documents

Recommendations

Info

Tools3 ToolsAdequate tools are required to <strong>service</strong> the WARP/M. <strong>ADB</strong> assumes no responsibility fordamage to units occurring from improper tools. These units will not be covered by thiswarranty.List of tools:• Screwdriver Philips Standard # 0• Screwdriver Philips Standard # 1• Screwdriver Philips Standard # 2• Screwdriver Positive Standard # 0• Screwdriver Positive Standard # 1• Screwdriver Positive Standard # 2• Screwdriver Flat 1• Screwdriver Flat 2• Screwdriver Flat 3• Nut driver set metric• Hex. driver set metric• Pliers• Cutter, pliers wrench setService Manual - page 6Issue 0.9www.adblighting.com
Spare Parts4 Spare Parts4.1 Code DescriptionThe chart below describes how the “Spare part numbers” are build-up.1001 . 6X . XXXStart digits forSpare Parts60: Conventional WARP61: Motorised WARP Head65: Motorised Yoke1001.60. XXX to 1001.61.XXX:• 000-190: Light Box• 200-290: Ring Compartment• 300-590: Lenses• 800-990: Mechanic1001.65.XXX:• 000-190: Top Box• 200-390: Boards• 400-590: Wiring• 600-790: Motors• 800-990: MechanicExample : 1001.61.0001001 => spare part61 => Motorised WARP Head000 => Light Boxwww.adblighting.com Service Manual - page 7Issue 0.9
Page 1: Motorised WARPService ManualIssue 0
Page 4 and 5: IndexIndexFOREWORD ................
Page 6 and 7: Introduction1 IntroductionAbout Thi
Page 10 and 11: Spare Parts4.2 Spare Parts for the
Page 12 and 13: Spare Parts4.2.2 Spare Parts for WA
Page 14 and 15: Spare PartsConnector cable Power 10
Page 16 and 17: Trouble Shooting5.2 Problems with T
Page 18 and 19: Trouble Shooting5.4 Problems with S
Page 20 and 21: Trouble Shooting5.5 Problems with a
Page 22 and 23: Technical Description6 Technical De
Page 24 and 25: Technical Description6.2.1 24 V Pow
Page 26 and 27: Technical Description6.2.3 Boards D
Page 28 and 29: Technical Description6.3.1.3 PCB 14
Page 30 and 31: Technical Description6.3.2 Pan & Ti
Page 32 and 33: Technical Description6.3.8 Descript
Page 34 and 35: Technical Description6.4 Wheels dri
Page 36 and 37: Technical DescriptionFunctions:This
Page 38 and 39: Technical DescriptionFunctions:This
Page 40 and 41: Motorised Yoke7 Motorised Yoke - Ma
Page 42 and 43: Motorised Yoke7.3 Open Motor WingRe
Page 44 and 45: Motorised Yoke7.5 Replace Front Pan
Page 46 and 47: Motorised Yoke7.7 Change Motor Boar
Page 48 and 49: Motorised Yoke7.9 Replace PCB Shutt
Page 50 and 51: Motorised Yoke7.11 Replace Top Box
Page 52 and 53: Motorised Yoke7.13 Replace Coarse P
Page 54 and 55: Motorised Yoke7.15 Replace Coarse T
Page 56 and 57: Motorised Yoke7.17 Remove WARP from
Page 58 and 59:
Motorised Yoke7.19 Replace Tilt MOT
Page 60 and 61:
Motorised Yoke7.21 Remove Coarse TI
Page 62 and 63:
Motorised Yoke7.22.2 How to install
Page 64 and 65:
Motorised Yoke7.22.2.2 Left Motor W
Page 66 and 67:
Motorised Yoke7.24 Remove Yoke from
Page 68 and 69:
Motorised Yoke7.25 Replace Pan Belt
Page 70 and 71:
Motorised Yoke7.27 IR Sensor Settin
Page 72 and 73:
Motorised Yoke7.28 Motor WingRequir
Page 74 and 75:
Motorised Yoke7.30 Adjust Motors in
Page 76 and 77:
Motorised Yoke8.1.2 How to place th
Page 78 and 79:
Motorised Yoke8.3 Replace the Refle
Page 80 and 81:
Motorised Yoke8.4.2 How replace the
Page 82 and 83:
WARP HeadWARP Head8.4.2.2 Introduce
Page 84 and 85:
WARP HeadWARP HeadPlace all graduat
Page 86 and 87:
WARP HeadWARP Head8.5 Replace the B
Page 88 and 89:
WARP HeadWARP Head8.7 Replace the B
Page 90 and 91:
WARP HeadWARP Head8.9 Change Gears
Page 92 and 93:
WARP HeadWARP Head8.11 Remove / Cha
Page 94 and 95:
WARP HeadWARP Head8.13 Replace Diap
Page 96:
WARP HeadWARP HeadService Manual -
show all

warp/m service manual - ADB Lighting Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?