warp/m service manual - ADB Lighting Technologies
warp/m service manual - ADB Lighting Technologies warp/m service manual - ADB Lighting Technologies
Motorised Yoke8.1.2 How to place the new lamp Assembly4 - Pass the safety cable through theLamp Cable hole of the new lamphandle.5 - Fix the safety cable on the new lampAssembly, using the Screw M3*6 (putthe washer between lamp plate andearth wire).SpringFinger Screw6 - Unclose the new Lamp Assembly usingthe 4 black taptite screws.7 - Screw the 2 Finger Screws with the 2springs.Service Manual - page 74Issue 0.9www.adblighting.com
Motorised Yoke8.2 Remove / Change the light BoxRequired Tool(s) Spare Part Code Preliminary readingHexagonal H4 1001.61.0201. Unplug the WARP and remove the lamp:2. Remove the WARP from the motorised Yoke (see chapter 7.17)3. Remove the 2 screws into the rings compartment using H44. Remove / Replace the Light Box and the 4 Plastic spacersChapter 7.17Chapter 7.22.1WARNING:Don’t forget the 4 plastic spacerswhen you replace the light Box1001.61.020 includes:• 1 complete light box• 2 Screws M5 * 40 + 2nuts• 4 plastic Spacers• 10 cable tie• 1 x 3-pole connectorPlastic Spacer2121www.adblighting.com Service Manual - page 75Issue 0.9
- Page 26 and 27: Technical Description6.2.3 Boards D
- Page 28 and 29: Technical Description6.3.1.3 PCB 14
- Page 30 and 31: Technical Description6.3.2 Pan & Ti
- Page 32 and 33: Technical Description6.3.8 Descript
- Page 34 and 35: Technical Description6.4 Wheels dri
- Page 36 and 37: Technical DescriptionFunctions:This
- Page 38 and 39: Technical DescriptionFunctions:This
- Page 40 and 41: Motorised Yoke7 Motorised Yoke - Ma
- Page 42 and 43: Motorised Yoke7.3 Open Motor WingRe
- Page 44 and 45: Motorised Yoke7.5 Replace Front Pan
- Page 46 and 47: Motorised Yoke7.7 Change Motor Boar
- Page 48 and 49: Motorised Yoke7.9 Replace PCB Shutt
- Page 50 and 51: Motorised Yoke7.11 Replace Top Box
- Page 52 and 53: Motorised Yoke7.13 Replace Coarse P
- Page 54 and 55: Motorised Yoke7.15 Replace Coarse T
- Page 56 and 57: Motorised Yoke7.17 Remove WARP from
- Page 58 and 59: Motorised Yoke7.19 Replace Tilt MOT
- Page 60 and 61: Motorised Yoke7.21 Remove Coarse TI
- Page 62 and 63: Motorised Yoke7.22.2 How to install
- Page 64 and 65: Motorised Yoke7.22.2.2 Left Motor W
- Page 66 and 67: Motorised Yoke7.24 Remove Yoke from
- Page 68 and 69: Motorised Yoke7.25 Replace Pan Belt
- Page 70 and 71: Motorised Yoke7.27 IR Sensor Settin
- Page 72 and 73: Motorised Yoke7.28 Motor WingRequir
- Page 74 and 75: Motorised Yoke7.30 Adjust Motors in
- Page 78 and 79: Motorised Yoke8.3 Replace the Refle
- Page 80 and 81: Motorised Yoke8.4.2 How replace the
- Page 82 and 83: WARP HeadWARP Head8.4.2.2 Introduce
- Page 84 and 85: WARP HeadWARP HeadPlace all graduat
- Page 86 and 87: WARP HeadWARP Head8.5 Replace the B
- Page 88 and 89: WARP HeadWARP Head8.7 Replace the B
- Page 90 and 91: WARP HeadWARP Head8.9 Change Gears
- Page 92 and 93: WARP HeadWARP Head8.11 Remove / Cha
- Page 94 and 95: WARP HeadWARP Head8.13 Replace Diap
- Page 96: WARP HeadWARP HeadService Manual -
Motorised Yoke8.2 Remove / Change the light BoxRequired Tool(s) Spare Part Code Preliminary readingHexagonal H4 1001.61.0201. Unplug the WARP and remove the lamp:2. Remove the WARP from the motorised Yoke (see chapter 7.17)3. Remove the 2 screws into the rings compartment using H44. Remove / Replace the Light Box and the 4 Plastic spacersChapter 7.17Chapter 7.22.1WARNING:Don’t forget the 4 plastic spacerswhen you replace the light Box1001.61.020 includes:• 1 complete light box• 2 Screws M5 * 40 + 2nuts• 4 plastic Spacers• 10 cable tie• 1 x 3-pole connectorPlastic Spacer2121www.adblighting.com Service Manual - page 75Issue 0.9