warp/m service manual - ADB Lighting Technologies

More documents

Recommendations

Info

Motorised Yoke7.30 Adjust Motors in the motor WingRequired Tool(s) Spare Part Code Preliminary readingOpen Ended Spanner 5,5Flat Screw DriverScrew driver PZ2None Chapter 7.28IMPORTANTWhen you remove the locking plate for maintenance, you have to adjust it before fixing andstart the WARP.It is very important to get free each motor to ensure a well working.1. Loosen the 2 screws of the locking plate (you can move it through the 2 obround)2. Adjust the locking plate position to leave 1 mm between it and all motors.3. Tighten the 2 screws.4. Control adjustment => Put the head up, Power on the WARP and control all reset1 mm When you press here, all gearsmust turn when you move theWARP Ring.Service Manual - page 72Issue 0.9www.adblighting.com
Motorised Yoke8 WARP HEAD - Maintenance Sheet8.1 How to change the lamp assembly8.1.1 How to remove the old lamp AssemblyRequired Tool(s) Spare Part Code Preliminary readingWire CutterFlat Screw DriverScrew Driver PZ21001.61.000Chapter 7.1Chapter 7.3Before Change the lamp Assembly Unplug the WARP and remove the lamp:1. Unplugged the Motorised WARP and remove the Lamp2. Remove Left Arm Cover and Left Motor Wing Cover3. Unplug Lamp Cable from the Relay Board (see chapter 6,1)4. Cut All cable ties which fit the lamp wire from the PCB relay to the Tilt shaft5. Cut the cable near the 3 pts connector.6. Slide the old wire through the Tilt Shaft7. Open the Lamp Holder8. Keep the security cable on the peak and flat cylinder9. Remove it from the old lamp assembly (screw which fix the earth wire).1001.61.000 includes:• 1 complete lamp assembly (with grip on wire)• 4 M3 * 10 Taptite+ 1 M3*6• 2 Finger screws + springs• 10 cable ties• 1 x 3-pole connectorwww.adblighting.com Service Manual - page 73Issue 0.9
Page 1:
Motorised WARPService ManualIssue 0
Page 4 and 5:
IndexIndexFOREWORD ................
Page 6 and 7:
Introduction1 IntroductionAbout Thi
Page 8 and 9:
Tools3 ToolsAdequate tools are requ
Page 10 and 11:
Spare Parts4.2 Spare Parts for the
Page 12 and 13:
Spare Parts4.2.2 Spare Parts for WA
Page 14 and 15:
Spare PartsConnector cable Power 10
Page 16 and 17:
Trouble Shooting5.2 Problems with T
Page 18 and 19:
Trouble Shooting5.4 Problems with S
Page 20 and 21:
Trouble Shooting5.5 Problems with a
Page 22 and 23:
Technical Description6 Technical De
Page 24 and 25: Technical Description6.2.1 24 V Pow
Page 26 and 27: Technical Description6.2.3 Boards D
Page 28 and 29: Technical Description6.3.1.3 PCB 14
Page 30 and 31: Technical Description6.3.2 Pan & Ti
Page 32 and 33: Technical Description6.3.8 Descript
Page 34 and 35: Technical Description6.4 Wheels dri
Page 36 and 37: Technical DescriptionFunctions:This
Page 38 and 39: Technical DescriptionFunctions:This
Page 40 and 41: Motorised Yoke7 Motorised Yoke - Ma
Page 42 and 43: Motorised Yoke7.3 Open Motor WingRe
Page 44 and 45: Motorised Yoke7.5 Replace Front Pan
Page 46 and 47: Motorised Yoke7.7 Change Motor Boar
Page 48 and 49: Motorised Yoke7.9 Replace PCB Shutt
Page 50 and 51: Motorised Yoke7.11 Replace Top Box
Page 52 and 53: Motorised Yoke7.13 Replace Coarse P
Page 54 and 55: Motorised Yoke7.15 Replace Coarse T
Page 56 and 57: Motorised Yoke7.17 Remove WARP from
Page 58 and 59: Motorised Yoke7.19 Replace Tilt MOT
Page 60 and 61: Motorised Yoke7.21 Remove Coarse TI
Page 62 and 63: Motorised Yoke7.22.2 How to install
Page 64 and 65: Motorised Yoke7.22.2.2 Left Motor W
Page 66 and 67: Motorised Yoke7.24 Remove Yoke from
Page 68 and 69: Motorised Yoke7.25 Replace Pan Belt
Page 70 and 71: Motorised Yoke7.27 IR Sensor Settin
Page 72 and 73: Motorised Yoke7.28 Motor WingRequir
Page 76 and 77: Motorised Yoke8.1.2 How to place th
Page 78 and 79: Motorised Yoke8.3 Replace the Refle
Page 80 and 81: Motorised Yoke8.4.2 How replace the
Page 82 and 83: WARP HeadWARP Head8.4.2.2 Introduce
Page 84 and 85: WARP HeadWARP HeadPlace all graduat
Page 86 and 87: WARP HeadWARP Head8.5 Replace the B
Page 88 and 89: WARP HeadWARP Head8.7 Replace the B
Page 90 and 91: WARP HeadWARP Head8.9 Change Gears
Page 92 and 93: WARP HeadWARP Head8.11 Remove / Cha
Page 94 and 95: WARP HeadWARP Head8.13 Replace Diap
Page 96: WARP HeadWARP HeadService Manual -
show all

warp/m service manual - ADB Lighting Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?