warp/m service manual - ADB Lighting Technologies

More documents

Recommendations

Info

Introduction1 IntroductionAbout This GuideThis manual is for the service and maintenance of WARP/M. It is intended to serve as areference for personnel who are trained in the service and repair of the WARP/M.WARP/M is warranted for one (1) year from the date of purchase. ADB assumes noresponsibility for damage to units occurring from improper service or being adjusted contraryto these instructions. These units will not be covered by this warranty.The following procedures are designed to be performed by a qualified service technician.This document is intended as a guide and does not provide the detail necessary for a noviceto make repairs.“Spare Parts Kit” list contains the parts required to make repairs described in this document.Always disconnect the power to the system before dismantling any component to avoidshorts and possible component damage.Service Manual - page 4Issue 0.9www.adblighting.com
Level Maintenance Description2 Level Maintenance Description2.1 Level DescriptionThe following chart describes three Maintenance levels:Level Description DocumentationWho:• Users• Theatre TechnicianLevel 1Level 2Level 3Action:• Usual Maintenance• Cleaning• Head Adjusting• Change Fuses• Clean IR Sensor• All access into Web Page• Load a new SoftwareWho:• Technician with ADB TrainingAction:• Access to all functions for normal operator• Replace mechanical sub-assembly• Replace Board• Change Ring Compartment• Send Back sub-assembly to ADB After SalesWho:• ADB After Sales or equivalentAction:• All accessUser ManualUser Manual+Service ManualInternalADBDocumentationThis guide is for qualified service technician level 2 and level 3.To become a qualified service technician level 2 a special training is necessary.Information about the level 2 trainings, please ask your local dealer or contact ADB.www.adblighting.com Service Manual - page 5Issue 0.9
Page 1: Motorised WARPService ManualIssue 0
Page 4 and 5: IndexIndexFOREWORD ................
Page 8 and 9: Tools3 ToolsAdequate tools are requ
Page 10 and 11: Spare Parts4.2 Spare Parts for the
Page 12 and 13: Spare Parts4.2.2 Spare Parts for WA
Page 14 and 15: Spare PartsConnector cable Power 10
Page 16 and 17: Trouble Shooting5.2 Problems with T
Page 18 and 19: Trouble Shooting5.4 Problems with S
Page 20 and 21: Trouble Shooting5.5 Problems with a
Page 22 and 23: Technical Description6 Technical De
Page 24 and 25: Technical Description6.2.1 24 V Pow
Page 26 and 27: Technical Description6.2.3 Boards D
Page 28 and 29: Technical Description6.3.1.3 PCB 14
Page 30 and 31: Technical Description6.3.2 Pan & Ti
Page 32 and 33: Technical Description6.3.8 Descript
Page 34 and 35: Technical Description6.4 Wheels dri
Page 36 and 37: Technical DescriptionFunctions:This
Page 38 and 39: Technical DescriptionFunctions:This
Page 40 and 41: Motorised Yoke7 Motorised Yoke - Ma
Page 42 and 43: Motorised Yoke7.3 Open Motor WingRe
Page 44 and 45: Motorised Yoke7.5 Replace Front Pan
Page 46 and 47: Motorised Yoke7.7 Change Motor Boar
Page 48 and 49: Motorised Yoke7.9 Replace PCB Shutt
Page 50 and 51: Motorised Yoke7.11 Replace Top Box
Page 52 and 53: Motorised Yoke7.13 Replace Coarse P
Page 54 and 55: Motorised Yoke7.15 Replace Coarse T
Page 56 and 57:
Motorised Yoke7.17 Remove WARP from
Page 58 and 59:
Motorised Yoke7.19 Replace Tilt MOT
Page 60 and 61:
Motorised Yoke7.21 Remove Coarse TI
Page 62 and 63:
Motorised Yoke7.22.2 How to install
Page 64 and 65:
Motorised Yoke7.22.2.2 Left Motor W
Page 66 and 67:
Motorised Yoke7.24 Remove Yoke from
Page 68 and 69:
Motorised Yoke7.25 Replace Pan Belt
Page 70 and 71:
Motorised Yoke7.27 IR Sensor Settin
Page 72 and 73:
Motorised Yoke7.28 Motor WingRequir
Page 74 and 75:
Motorised Yoke7.30 Adjust Motors in
Page 76 and 77:
Motorised Yoke8.1.2 How to place th
Page 78 and 79:
Motorised Yoke8.3 Replace the Refle
Page 80 and 81:
Motorised Yoke8.4.2 How replace the
Page 82 and 83:
WARP HeadWARP Head8.4.2.2 Introduce
Page 84 and 85:
WARP HeadWARP HeadPlace all graduat
Page 86 and 87:
WARP HeadWARP Head8.5 Replace the B
Page 88 and 89:
WARP HeadWARP Head8.7 Replace the B
Page 90 and 91:
WARP HeadWARP Head8.9 Change Gears
Page 92 and 93:
WARP HeadWARP Head8.11 Remove / Cha
Page 94 and 95:
WARP HeadWARP Head8.13 Replace Diap
Page 96:
WARP HeadWARP HeadService Manual -
show all

warp/m service manual - ADB Lighting Technologies

Create successful ePaper yourself

Delete template?

Save as template?