warp/m service manual - ADB Lighting Technologies

More documents

Recommendations

Info

Motorised Yoke7.17 Remove WARP from the YOKERequired Tool(s) Spare Part Code Preliminary readingWARP KeyScrewdriver PZ2AMP Pin CrimpAMP Pin Extract Tool1001.65.880Chapter 7.1Chapter 7.2Chapter 6.11. Switch OFF and Unplug the WARP2. Open Arms cover and Disconnect lamp cable into the left arm.3. Use the special tool to extract pin from the AMP Connector, if not cut the cable4. Remove Motor Wing Cover (see chapter 7.2)5. Unplug and remove all Cables from Motor Wing through Tilt shaft (Motors, IR Sensor andXLR 4)6. Loosen Nut Right and Left between Arms and Motor Wing7. Slide the WARP through the Motor Wing Profile and pass lamp cable through the Tilt Shaft.Notice:• If you haven’t got a Pin Extract Tool, you can orderspare part 1001.65.880, which provides you newconnector and crimp pin. So you can cut wire nearthe existing one and replace it to re-assemble theWARP.Direction of Arrow = tountighten1001.65.8801001.65.880 includes:• 4 Pins• 1 Connector• 5 cable ties• 40 Screws M4*12 ZN• Thermo shrink sleeve• 4 cable tiesService Manual - page 54Issue 0.9www.adblighting.com
Motorised Yoke7.18 Remove Right ArmRequired Tool(s) Spare Part Code Preliminary readingHexagon Key4Circlips Pliers 177 G 18Wire Cutter1001.65.890Chapter 7.1Chapter 7.7Chapter 7.171001.65.890 includes:1. Switch OFF and Unplug the WARP• 1 Motor system housing tilt2. Remove Right Board (see chapter 7.7)• 11 Screws M6*10• 10 Tie Rape3. Remove all cable fixed by tie-rape on the right armstructure4. Disconnect: Tilt Motor – AMR Fine Tilt Sensor – AMR Coarse Tilt Sensor5. Remove Circlips, Tilt Shaft Plate and the nut6. Remove the 10 screws on the two sides7. Replace the Motor Tilt Assembly4 3 2 16Tilt Shaft Plate51001.65.890Important:• When you replace Tilt Shaft plate,place it in the right position.• After this operation, you have torecalibrate the Tilt from desk or Webpage with the last <strong>ADB</strong> softwarewww.adblighting.com Service Manual - page 55Issue 0.9
Page 1:
Motorised WARPService ManualIssue 0
Page 4 and 5:
IndexIndexFOREWORD ................
Page 6 and 7: Introduction1 IntroductionAbout Thi
Page 8 and 9: Tools3 ToolsAdequate tools are requ
Page 10 and 11: Spare Parts4.2 Spare Parts for the
Page 12 and 13: Spare Parts4.2.2 Spare Parts for WA
Page 14 and 15: Spare PartsConnector cable Power 10
Page 16 and 17: Trouble Shooting5.2 Problems with T
Page 18 and 19: Trouble Shooting5.4 Problems with S
Page 20 and 21: Trouble Shooting5.5 Problems with a
Page 22 and 23: Technical Description6 Technical De
Page 24 and 25: Technical Description6.2.1 24 V Pow
Page 26 and 27: Technical Description6.2.3 Boards D
Page 28 and 29: Technical Description6.3.1.3 PCB 14
Page 30 and 31: Technical Description6.3.2 Pan & Ti
Page 32 and 33: Technical Description6.3.8 Descript
Page 34 and 35: Technical Description6.4 Wheels dri
Page 36 and 37: Technical DescriptionFunctions:This
Page 38 and 39: Technical DescriptionFunctions:This
Page 40 and 41: Motorised Yoke7 Motorised Yoke - Ma
Page 42 and 43: Motorised Yoke7.3 Open Motor WingRe
Page 44 and 45: Motorised Yoke7.5 Replace Front Pan
Page 46 and 47: Motorised Yoke7.7 Change Motor Boar
Page 48 and 49: Motorised Yoke7.9 Replace PCB Shutt
Page 50 and 51: Motorised Yoke7.11 Replace Top Box
Page 52 and 53: Motorised Yoke7.13 Replace Coarse P
Page 54 and 55: Motorised Yoke7.15 Replace Coarse T
Page 58 and 59: Motorised Yoke7.19 Replace Tilt MOT
Page 60 and 61: Motorised Yoke7.21 Remove Coarse TI
Page 62 and 63: Motorised Yoke7.22.2 How to install
Page 64 and 65: Motorised Yoke7.22.2.2 Left Motor W
Page 66 and 67: Motorised Yoke7.24 Remove Yoke from
Page 68 and 69: Motorised Yoke7.25 Replace Pan Belt
Page 70 and 71: Motorised Yoke7.27 IR Sensor Settin
Page 72 and 73: Motorised Yoke7.28 Motor WingRequir
Page 74 and 75: Motorised Yoke7.30 Adjust Motors in
Page 76 and 77: Motorised Yoke8.1.2 How to place th
Page 78 and 79: Motorised Yoke8.3 Replace the Refle
Page 80 and 81: Motorised Yoke8.4.2 How replace the
Page 82 and 83: WARP HeadWARP Head8.4.2.2 Introduce
Page 84 and 85: WARP HeadWARP HeadPlace all graduat
Page 86 and 87: WARP HeadWARP Head8.5 Replace the B
Page 88 and 89: WARP HeadWARP Head8.7 Replace the B
Page 90 and 91: WARP HeadWARP Head8.9 Change Gears
Page 92 and 93: WARP HeadWARP Head8.11 Remove / Cha
Page 94 and 95: WARP HeadWARP Head8.13 Replace Diap
Page 96: WARP HeadWARP HeadService Manual -
show all

warp/m service manual - ADB Lighting Technologies

Create successful ePaper yourself

Delete template?

Save as template?