warp/m service manual - ADB Lighting Technologies

More documents

Recommendations

Info

Motorised Yoke7.15 Replace Coarse TILT AMR SensorRequired Tool(s) Spare Part Code Preliminary readingScrewdriver PZ2Wire Cutter1001.65.230Chapter 7.1Chapter 7.7Chapter 6.11001.65.230 includes:1. Switch OFF and Unplug the WARP• 1 Sensor cable• 3 Screws M3*102. Remove Right Board (see chapter 7.7)• 3 Washers + 3 nuts3. Cut The cable tie and Disconnect Coarse Tilt sensor wire • 2 cable ties4. Remove the 4 taptite screws on the two sides of the arm.5. Slide down the Sensor Plate until access all screws of the AMR Sensor6. Replace the Magnetic Sensor using new screws2Important:• The first time you replace Coarse Tilt AMRSENSOR, you have to replace all taptitescrews By TCBC M4x8 ZN DIN 7985-Z.• When you re-start the WARP you have to recalibratePAN AXIS.• This can be started from web page or desk orlocal display.1001.65.2302431Note:• Distance between sensor andmagnet should be around 1 mm• You have small windows on thearm side to inspect the sensorpositionService Manual - page 52Issue 0.9www.adblighting.com
Motorised Yoke7.16 Replace TILT BeltRequired Tool(s) Spare Part Code Preliminary readingScrewdriver PZ2H 51001.65.680Chapter 7.1Chapter 7.7Chapter 7.141. Switch OFF and Unplug the WARP2. Remove Right Board (see chapter 7.7) and the Fine AMR Sensor (see chapter 7.14)3. Loose 4 screws on the Tilt Motor Suspension Plate4. Slide up the Motor to get free the Belt5. Remove the belt turning the Tilt axis1001.65.680 includes:• 1 Belt• 2 Screws M3*108• 2 Washers + 2 nuts4Important:• If you remove the Fine Tilt Sensor, youhave to replace all taptite screws ByTCBC M4x8 ZN DIN 7985-Z.• When you re-start the WARP aftermoving AMR Sensor, you have to recalibratePAN AXIS.• This can be started from web page ordesk or local display.1001.65.68021: Loosen the 4 Screws3www.adblighting.com Service Manual - page 53Issue 0.9
Page 1:
Motorised WARPService ManualIssue 0
Page 4 and 5: IndexIndexFOREWORD ................
Page 6 and 7: Introduction1 IntroductionAbout Thi
Page 8 and 9: Tools3 ToolsAdequate tools are requ
Page 10 and 11: Spare Parts4.2 Spare Parts for the
Page 12 and 13: Spare Parts4.2.2 Spare Parts for WA
Page 14 and 15: Spare PartsConnector cable Power 10
Page 16 and 17: Trouble Shooting5.2 Problems with T
Page 18 and 19: Trouble Shooting5.4 Problems with S
Page 20 and 21: Trouble Shooting5.5 Problems with a
Page 22 and 23: Technical Description6 Technical De
Page 24 and 25: Technical Description6.2.1 24 V Pow
Page 26 and 27: Technical Description6.2.3 Boards D
Page 28 and 29: Technical Description6.3.1.3 PCB 14
Page 30 and 31: Technical Description6.3.2 Pan & Ti
Page 32 and 33: Technical Description6.3.8 Descript
Page 34 and 35: Technical Description6.4 Wheels dri
Page 36 and 37: Technical DescriptionFunctions:This
Page 38 and 39: Technical DescriptionFunctions:This
Page 40 and 41: Motorised Yoke7 Motorised Yoke - Ma
Page 42 and 43: Motorised Yoke7.3 Open Motor WingRe
Page 44 and 45: Motorised Yoke7.5 Replace Front Pan
Page 46 and 47: Motorised Yoke7.7 Change Motor Boar
Page 48 and 49: Motorised Yoke7.9 Replace PCB Shutt
Page 50 and 51: Motorised Yoke7.11 Replace Top Box
Page 52 and 53: Motorised Yoke7.13 Replace Coarse P
Page 56 and 57: Motorised Yoke7.17 Remove WARP from
Page 58 and 59: Motorised Yoke7.19 Replace Tilt MOT
Page 60 and 61: Motorised Yoke7.21 Remove Coarse TI
Page 62 and 63: Motorised Yoke7.22.2 How to install
Page 64 and 65: Motorised Yoke7.22.2.2 Left Motor W
Page 66 and 67: Motorised Yoke7.24 Remove Yoke from
Page 68 and 69: Motorised Yoke7.25 Replace Pan Belt
Page 70 and 71: Motorised Yoke7.27 IR Sensor Settin
Page 72 and 73: Motorised Yoke7.28 Motor WingRequir
Page 74 and 75: Motorised Yoke7.30 Adjust Motors in
Page 76 and 77: Motorised Yoke8.1.2 How to place th
Page 78 and 79: Motorised Yoke8.3 Replace the Refle
Page 80 and 81: Motorised Yoke8.4.2 How replace the
Page 82 and 83: WARP HeadWARP Head8.4.2.2 Introduce
Page 84 and 85: WARP HeadWARP HeadPlace all graduat
Page 86 and 87: WARP HeadWARP Head8.5 Replace the B
Page 88 and 89: WARP HeadWARP Head8.7 Replace the B
Page 90 and 91: WARP HeadWARP Head8.9 Change Gears
Page 92 and 93: WARP HeadWARP Head8.11 Remove / Cha
Page 94 and 95: WARP HeadWARP Head8.13 Replace Diap
Page 96: WARP HeadWARP HeadService Manual -
show all

warp/m service manual - ADB Lighting Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?