warp/m service manual - ADB Lighting Technologies

More documents

Recommendations

Info

Technical DescriptionFunctions:This board PCB 1525 is designed to:• Control all Motors in the Left Motor Wing: Shutter B, Shutter C, Front Acc. And ZoomComponents:Components you can change on this board are:• Fuse 2A (spare part code 1001.65.300)Reset procedure:When you switch On the WARP/M, all shutter rings will turn automatically to the IR Sensor.When the Silvered index of the ring passes in front of the IR Sensor, the ring stops and goes back tothe 0 position.If the ring doesn’t stop in front of the IR sensor, the reset has failed.In this case, send a calibration as explain in the user <strong>manual</strong>.Service Manual - page 34Issue 0.9www.adblighting.com
Technical Description6.4.3 Right 6 Drivers BoardSPARE PART CODE 1001.65.220LOCATIONRight ArmLINKShutters A & DWARP Link 1 & 2IR Sensor RightDMX for CC changerFuse Motor R6:Shutter AFuse Motor R5:Shutter DFuse Motor R4:Accessory 1Fuse Motor R2:Shutter DFuse Motor R3:Shutter AFuse Motor R1:FocusIR SensorConnectorWARP LINK 2DMX Out forColour ChangerWARP LINK 1www.adblighting.com Service Manual - page 35Issue 0.9
Page 1: Motorised WARPService ManualIssue 0
Page 4 and 5: IndexIndexFOREWORD ................
Page 6 and 7: Introduction1 IntroductionAbout Thi
Page 8 and 9: Tools3 ToolsAdequate tools are requ
Page 10 and 11: Spare Parts4.2 Spare Parts for the
Page 12 and 13: Spare Parts4.2.2 Spare Parts for WA
Page 14 and 15: Spare PartsConnector cable Power 10
Page 16 and 17: Trouble Shooting5.2 Problems with T
Page 18 and 19: Trouble Shooting5.4 Problems with S
Page 20 and 21: Trouble Shooting5.5 Problems with a
Page 22 and 23: Technical Description6 Technical De
Page 24 and 25: Technical Description6.2.1 24 V Pow
Page 26 and 27: Technical Description6.2.3 Boards D
Page 28 and 29: Technical Description6.3.1.3 PCB 14
Page 30 and 31: Technical Description6.3.2 Pan & Ti
Page 32 and 33: Technical Description6.3.8 Descript
Page 34 and 35: Technical Description6.4 Wheels dri
Page 38 and 39: Technical DescriptionFunctions:This
Page 40 and 41: Motorised Yoke7 Motorised Yoke - Ma
Page 42 and 43: Motorised Yoke7.3 Open Motor WingRe
Page 44 and 45: Motorised Yoke7.5 Replace Front Pan
Page 46 and 47: Motorised Yoke7.7 Change Motor Boar
Page 48 and 49: Motorised Yoke7.9 Replace PCB Shutt
Page 50 and 51: Motorised Yoke7.11 Replace Top Box
Page 52 and 53: Motorised Yoke7.13 Replace Coarse P
Page 54 and 55: Motorised Yoke7.15 Replace Coarse T
Page 56 and 57: Motorised Yoke7.17 Remove WARP from
Page 58 and 59: Motorised Yoke7.19 Replace Tilt MOT
Page 60 and 61: Motorised Yoke7.21 Remove Coarse TI
Page 62 and 63: Motorised Yoke7.22.2 How to install
Page 64 and 65: Motorised Yoke7.22.2.2 Left Motor W
Page 66 and 67: Motorised Yoke7.24 Remove Yoke from
Page 68 and 69: Motorised Yoke7.25 Replace Pan Belt
Page 70 and 71: Motorised Yoke7.27 IR Sensor Settin
Page 72 and 73: Motorised Yoke7.28 Motor WingRequir
Page 74 and 75: Motorised Yoke7.30 Adjust Motors in
Page 76 and 77: Motorised Yoke8.1.2 How to place th
Page 78 and 79: Motorised Yoke8.3 Replace the Refle
Page 80 and 81: Motorised Yoke8.4.2 How replace the
Page 82 and 83: WARP HeadWARP Head8.4.2.2 Introduce
Page 84 and 85: WARP HeadWARP HeadPlace all graduat
Page 86 and 87:
WARP HeadWARP Head8.5 Replace the B
Page 88 and 89:
WARP HeadWARP Head8.7 Replace the B
Page 90 and 91:
WARP HeadWARP Head8.9 Change Gears
Page 92 and 93:
WARP HeadWARP Head8.11 Remove / Cha
Page 94 and 95:
WARP HeadWARP Head8.13 Replace Diap
Page 96:
WARP HeadWARP HeadService Manual -
show all

warp/m service manual - ADB Lighting Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?