warp/m service manual - ADB Lighting Technologies
warp/m service manual - ADB Lighting Technologies warp/m service manual - ADB Lighting Technologies
Technical Description6.3.1.3 PCB 1494Front:ESC BUTTONFUSE 3AENTER BUTTONERROR LEDDMX LEDDMX INPOWER LEDDMX OUTETHERNETBack:DISPLAYBUTTON -Important:2 Last slots must be freeBUTTON +ETHERNET LED24 V DCINTERNAL DIMMER WARP LINK 1Service Manual - page 26Issue 0.9www.adblighting.com
Technical Description6.3.1.4 Functions:This board PCB 1496 is designed to:• Receive / Send DMX 512• Translate DMX in WARP Protocol• Ethernet communication• Control and Supply of the Motor Boards• Technician Interface (Display Menu)• Control of built-in dimmer and ballast (for WARP/M/DIM and WARP/H/HMI)• Update of software in other boards6.3.1.5 Components:Components you can change on this board are:• Fuse 3A (spare part code 1001.65.300)• Display (see front photo: 2 last slots are free)6.3.1.6 Power-up procedure:When you switch on the WARP/M1. Only LED Power on2. Wait approximately 30 s until all LED is on and Display write WARP or DMX- before motorsresettingwww.adblighting.com Service Manual - page 27Issue 0.9
- Page 1: Motorised WARPService ManualIssue 0
- Page 4 and 5: IndexIndexFOREWORD ................
- Page 6 and 7: Introduction1 IntroductionAbout Thi
- Page 8 and 9: Tools3 ToolsAdequate tools are requ
- Page 10 and 11: Spare Parts4.2 Spare Parts for the
- Page 12 and 13: Spare Parts4.2.2 Spare Parts for WA
- Page 14 and 15: Spare PartsConnector cable Power 10
- Page 16 and 17: Trouble Shooting5.2 Problems with T
- Page 18 and 19: Trouble Shooting5.4 Problems with S
- Page 20 and 21: Trouble Shooting5.5 Problems with a
- Page 22 and 23: Technical Description6 Technical De
- Page 24 and 25: Technical Description6.2.1 24 V Pow
- Page 26 and 27: Technical Description6.2.3 Boards D
- Page 30 and 31: Technical Description6.3.2 Pan & Ti
- Page 32 and 33: Technical Description6.3.8 Descript
- Page 34 and 35: Technical Description6.4 Wheels dri
- Page 36 and 37: Technical DescriptionFunctions:This
- Page 38 and 39: Technical DescriptionFunctions:This
- Page 40 and 41: Motorised Yoke7 Motorised Yoke - Ma
- Page 42 and 43: Motorised Yoke7.3 Open Motor WingRe
- Page 44 and 45: Motorised Yoke7.5 Replace Front Pan
- Page 46 and 47: Motorised Yoke7.7 Change Motor Boar
- Page 48 and 49: Motorised Yoke7.9 Replace PCB Shutt
- Page 50 and 51: Motorised Yoke7.11 Replace Top Box
- Page 52 and 53: Motorised Yoke7.13 Replace Coarse P
- Page 54 and 55: Motorised Yoke7.15 Replace Coarse T
- Page 56 and 57: Motorised Yoke7.17 Remove WARP from
- Page 58 and 59: Motorised Yoke7.19 Replace Tilt MOT
- Page 60 and 61: Motorised Yoke7.21 Remove Coarse TI
- Page 62 and 63: Motorised Yoke7.22.2 How to install
- Page 64 and 65: Motorised Yoke7.22.2.2 Left Motor W
- Page 66 and 67: Motorised Yoke7.24 Remove Yoke from
- Page 68 and 69: Motorised Yoke7.25 Replace Pan Belt
- Page 70 and 71: Motorised Yoke7.27 IR Sensor Settin
- Page 72 and 73: Motorised Yoke7.28 Motor WingRequir
- Page 74 and 75: Motorised Yoke7.30 Adjust Motors in
- Page 76 and 77: Motorised Yoke8.1.2 How to place th
Technical Description6.3.1.4 Functions:This board PCB 1496 is designed to:• Receive / Send DMX 512• Translate DMX in WARP Protocol• Ethernet communication• Control and Supply of the Motor Boards• Technician Interface (Display Menu)• Control of built-in dimmer and ballast (for WARP/M/DIM and WARP/H/HMI)• Update of software in other boards6.3.1.5 Components:Components you can change on this board are:• Fuse 3A (spare part code 1001.65.300)• Display (see front photo: 2 last slots are free)6.3.1.6 Power-up procedure:When you switch on the WARP/M1. Only LED Power on2. Wait approximately 30 s until all LED is on and Display write WARP or DMX- before motorsresettingwww.adblighting.com Service Manual - page 27Issue 0.9