warp/m service manual - ADB Lighting Technologies

More documents

Recommendations

Info

Technical Description6.2.1 24 V Power Supply6.2.1.1 DescriptionSPARE PART CODE 1001.65.010LOCATIONTOP BOXLINKSIn: Mains VoltageOut: Top BoardThe WARP/M is powered with 198 - 264 V AC, +/- 50/60 Hz (optional: universal power supply90 – 264 V, +/- 50/60 Hz). The connector is Neutrix PowerCon locking.The WARP/M is protected with a fuse of 6.3 A 250V SPT 5 x 20 mm.The lamp power is coming from an external dimmer.Power SupplyFuseLamp Supply6.2.1.2 How to know that the 24 V Power Supply present.It the “power” LED is on at power up of the WARP/M the 24 V supply is present. If the power LED isoff the 24 V power supply is not available. (refer to chapter 7.4.)For the early production units (production batch 1 to 10) the LED will only light up after the booting ofthe WARP/M (+/- 1 min). A quick way to check if the 24 V power supply is present is trying to movethe yoke just after power on. If Pan & Tilt Motors give resistance, the 24 V is present; if not, controlthe supply (refer to chapter 7.4.).Service Manual - page 22Issue 0.9www.adblighting.com
Technical Description6.2.2 Motors functionalitiesThe drawing below defines each motor with his associated function.R1 FocalR2 Shutter 4R3 Shutter 1R4 Accessory 1 (rear)R5 Shutter 4R6 Shutter 1L1 Shutter 2L2 Shutter 3L3 Accessory 2 (front)L4 Shutter 2L5 Shutter 3L6 ZoomRight hand motorwingR3R2R1L1L2L3Left hand motorwingL6L5R6R5L4R4TILTMOTORPANMOTORwww.adblighting.com Service Manual - page 23Issue 0.9
Page 1: Motorised WARPService ManualIssue 0
Page 4 and 5: IndexIndexFOREWORD ................
Page 6 and 7: Introduction1 IntroductionAbout Thi
Page 8 and 9: Tools3 ToolsAdequate tools are requ
Page 10 and 11: Spare Parts4.2 Spare Parts for the
Page 12 and 13: Spare Parts4.2.2 Spare Parts for WA
Page 14 and 15: Spare PartsConnector cable Power 10
Page 16 and 17: Trouble Shooting5.2 Problems with T
Page 18 and 19: Trouble Shooting5.4 Problems with S
Page 20 and 21: Trouble Shooting5.5 Problems with a
Page 22 and 23: Technical Description6 Technical De
Page 26 and 27: Technical Description6.2.3 Boards D
Page 28 and 29: Technical Description6.3.1.3 PCB 14
Page 30 and 31: Technical Description6.3.2 Pan & Ti
Page 32 and 33: Technical Description6.3.8 Descript
Page 34 and 35: Technical Description6.4 Wheels dri
Page 36 and 37: Technical DescriptionFunctions:This
Page 38 and 39: Technical DescriptionFunctions:This
Page 40 and 41: Motorised Yoke7 Motorised Yoke - Ma
Page 42 and 43: Motorised Yoke7.3 Open Motor WingRe
Page 44 and 45: Motorised Yoke7.5 Replace Front Pan
Page 46 and 47: Motorised Yoke7.7 Change Motor Boar
Page 48 and 49: Motorised Yoke7.9 Replace PCB Shutt
Page 50 and 51: Motorised Yoke7.11 Replace Top Box
Page 52 and 53: Motorised Yoke7.13 Replace Coarse P
Page 54 and 55: Motorised Yoke7.15 Replace Coarse T
Page 56 and 57: Motorised Yoke7.17 Remove WARP from
Page 58 and 59: Motorised Yoke7.19 Replace Tilt MOT
Page 60 and 61: Motorised Yoke7.21 Remove Coarse TI
Page 62 and 63: Motorised Yoke7.22.2 How to install
Page 64 and 65: Motorised Yoke7.22.2.2 Left Motor W
Page 66 and 67: Motorised Yoke7.24 Remove Yoke from
Page 68 and 69: Motorised Yoke7.25 Replace Pan Belt
Page 70 and 71: Motorised Yoke7.27 IR Sensor Settin
Page 72 and 73: Motorised Yoke7.28 Motor WingRequir
Page 74 and 75:
Motorised Yoke7.30 Adjust Motors in
Page 76 and 77:
Motorised Yoke8.1.2 How to place th
Page 78 and 79:
Motorised Yoke8.3 Replace the Refle
Page 80 and 81:
Motorised Yoke8.4.2 How replace the
Page 82 and 83:
WARP HeadWARP Head8.4.2.2 Introduce
Page 84 and 85:
WARP HeadWARP HeadPlace all graduat
Page 86 and 87:
WARP HeadWARP Head8.5 Replace the B
Page 88 and 89:
WARP HeadWARP Head8.7 Replace the B
Page 90 and 91:
WARP HeadWARP Head8.9 Change Gears
Page 92 and 93:
WARP HeadWARP Head8.11 Remove / Cha
Page 94 and 95:
WARP HeadWARP Head8.13 Replace Diap
Page 96:
WARP HeadWARP HeadService Manual -
show all

warp/m service manual - ADB Lighting Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?