warp/m service manual - ADB Lighting Technologies
warp/m service manual - ADB Lighting Technologies warp/m service manual - ADB Lighting Technologies
Trouble Shooting5.2 Problems with Top-Box and DisplayTrouble/Symptom Origin SolutionMain Supply Fuse is blown Control and Change Main Fuse (seeuser Manual)NO24 V Cable Unplugged orGround and +24 v wireinverted (see chapter 6.1 forelectrical connection)Control 24 V power supply ConnectionNo Display after 1 min. powerOnNO24 V Supply Out of order (seechapter 6.3.1 to verifyvoltages)Replace 24 V power supply (seechapter 7.4)NOTop Box Board Out of orderReplace top Box Board (see chapter7.5)No Control of the WARP byArt NetBad Ethernet ConnectionNOBad Ethernet ConfigurationControl and replace external DataCable (Ethernet LED must flicker)Control Sub-net and Universe on theWARP Web PageService Manual - page 14Issue 0.9www.adblighting.com
5.3 Problems with Pan & TiltTrouble ShootingImportant: On this chapter, consider that Top Board and 24V Power Supply are not damagedTrouble/Symptom Origin SolutionMove the yoke manually andcontrol if there is motorresistanceNOPan “or” Tilt don’t MovePan “or” Tilt Fuse is warmNOReplace warm fuse (see chapter 6.3.3)Pan & Tilt Board is out of orderReplace Pan & Tilt BoardBad Calibration of Pan or TiltNORe- Calibrate Pan & TiltOne of the 2 sensors (fine andcoarse) is disconnectedControl all Sensor connections andwiringPan “or” Tilt is not StableNOOne of the 2 sensors (fine andcoarse) is damagedNOReplace Fine and Coarse AMR sensors(See chapter 7.12 for Pan and 7.13 forTilt)Pan and Tilt Board is damagedBad Calibration of Pan or TiltReplace Pan & Tilt Board (see chapter7.8)Re- Calibrate Pan “or” TiltNOPan “or” Tilt make noise at 0or Full after resettingWiring problem between AMRSensors and BoardNOControl and change damaged wireOne of the 2 sensors (fine andcoarse) is damagedReplace Fine and Coarse AMR sensors(See chapter 7.12 for Pan and 7.13 forTilt)www.adblighting.com Service Manual - page 15Issue 0.9
- Page 1: Motorised WARPService ManualIssue 0
- Page 4 and 5: IndexIndexFOREWORD ................
- Page 6 and 7: Introduction1 IntroductionAbout Thi
- Page 8 and 9: Tools3 ToolsAdequate tools are requ
- Page 10 and 11: Spare Parts4.2 Spare Parts for the
- Page 12 and 13: Spare Parts4.2.2 Spare Parts for WA
- Page 14 and 15: Spare PartsConnector cable Power 10
- Page 18 and 19: Trouble Shooting5.4 Problems with S
- Page 20 and 21: Trouble Shooting5.5 Problems with a
- Page 22 and 23: Technical Description6 Technical De
- Page 24 and 25: Technical Description6.2.1 24 V Pow
- Page 26 and 27: Technical Description6.2.3 Boards D
- Page 28 and 29: Technical Description6.3.1.3 PCB 14
- Page 30 and 31: Technical Description6.3.2 Pan & Ti
- Page 32 and 33: Technical Description6.3.8 Descript
- Page 34 and 35: Technical Description6.4 Wheels dri
- Page 36 and 37: Technical DescriptionFunctions:This
- Page 38 and 39: Technical DescriptionFunctions:This
- Page 40 and 41: Motorised Yoke7 Motorised Yoke - Ma
- Page 42 and 43: Motorised Yoke7.3 Open Motor WingRe
- Page 44 and 45: Motorised Yoke7.5 Replace Front Pan
- Page 46 and 47: Motorised Yoke7.7 Change Motor Boar
- Page 48 and 49: Motorised Yoke7.9 Replace PCB Shutt
- Page 50 and 51: Motorised Yoke7.11 Replace Top Box
- Page 52 and 53: Motorised Yoke7.13 Replace Coarse P
- Page 54 and 55: Motorised Yoke7.15 Replace Coarse T
- Page 56 and 57: Motorised Yoke7.17 Remove WARP from
- Page 58 and 59: Motorised Yoke7.19 Replace Tilt MOT
- Page 60 and 61: Motorised Yoke7.21 Remove Coarse TI
- Page 62 and 63: Motorised Yoke7.22.2 How to install
- Page 64 and 65: Motorised Yoke7.22.2.2 Left Motor W
5.3 Problems with Pan & TiltTrouble ShootingImportant: On this chapter, consider that Top Board and 24V Power Supply are not damagedTrouble/Symptom Origin SolutionMove the yoke <strong>manual</strong>ly andcontrol if there is motorresistanceNOPan “or” Tilt don’t MovePan “or” Tilt Fuse is warmNOReplace warm fuse (see chapter 6.3.3)Pan & Tilt Board is out of orderReplace Pan & Tilt BoardBad Calibration of Pan or TiltNORe- Calibrate Pan & TiltOne of the 2 sensors (fine andcoarse) is disconnectedControl all Sensor connections andwiringPan “or” Tilt is not StableNOOne of the 2 sensors (fine andcoarse) is damagedNOReplace Fine and Coarse AMR sensors(See chapter 7.12 for Pan and 7.13 forTilt)Pan and Tilt Board is damagedBad Calibration of Pan or TiltReplace Pan & Tilt Board (see chapter7.8)Re- Calibrate Pan “or” TiltNOPan “or” Tilt make noise at 0or Full after resettingWiring problem between AMRSensors and BoardNOControl and change damaged wireOne of the 2 sensors (fine andcoarse) is damagedReplace Fine and Coarse AMR sensors(See chapter 7.12 for Pan and 7.13 forTilt)www.adblighting.com Service Manual - page 15Issue 0.9