MS Thesis R. Hager - Hawaii National Marine Renewable Energy ...
MS Thesis R. Hager - Hawaii National Marine Renewable Energy ... MS Thesis R. Hager - Hawaii National Marine Renewable Energy ...
12. Delete all lines inside the curve.13. Return to the isometric view by selecting the icon.14. Add the body’s width to the body by selecting the icon.15. Edit the body’s width details under Details of Extrude 1 in the Details View.Set the Direction to Both-Symmetric, and Depth to 2.9375 in. (7.46 cm), asseen in Figure 4.8.Figure 4. 8 Extruding the Body16. After editing the Details of the Extrude 1, select the icon.17. Create a surface rather than a body by selecting the icon.18. Edit the surface details under Details of Thin 1. Set the Selection Type toBodies Only. Set the Thickness to 0 in., as seen in Figure 4.9. Highlight thebody and select Apply under Selection Type.62
19. Select the Generate icon.Figure 4. 9 Details of Thin20. Select Freeze under the Tools menu, as seen in Figure 4.10.Figure 4. 10 Freezing a Body21. Select Slice under the Create menu, as seen in Figure 4.11.Figure 4. 11 Slicing a Body63
- Page 11 and 12: 1.2 Advantages of Wave EnergyAdvant
- Page 13 and 14: for various projects. Included in t
- Page 15 and 16: pollution would occur from hydrauli
- Page 17 and 18: Figure 1. 7 Average Annual Wave Pow
- Page 19 and 20: Backer (2009) numerically and exper
- Page 21 and 22: CHAPTER 2. WAVE ENERGY CONVERSION D
- Page 23 and 24: 2.3 OrientationOrientation is defin
- Page 25 and 26: Figure 2.4 Oscillating Water Column
- Page 27 and 28: 2.5 Reference PointMeans of reactio
- Page 29 and 30: Linear GeneratorTurbineRotary Gener
- Page 31 and 32: Table 2. 1 WEC ClassificationsDevic
- Page 33 and 34: 33P.T.O.MooringReferencePointOperat
- Page 35 and 36: CHAPTER 3. THEORY AND GOVERNING EQU
- Page 37 and 38: F(x,z,t) z 0DFDtFt u F 0 0 (4
- Page 39 and 40: in ni(13)on S for i=1, 3in( r n)i3
- Page 41 and 42: I iAg e ekz i( kx t)(30)cosh( k(z
- Page 44 and 45: where ijkis the permutation symbol.
- Page 46 and 47: Mw k ieitS( D I) ijkrinjdS(46)3.3.3
- Page 48 and 49: Due to Kirchhoff decomposition, rec
- Page 50 and 51: TE KE PE 20L Asin(kx) 1 2(61)dV d
- Page 52 and 53: P I Iw dS (70)tnSIf the column
- Page 54 and 55: 221 2P gA C(77)max g2 3.8 Maximum
- Page 56 and 57: 4.2 AQWA Modeling ProcedureThe user
- Page 58 and 59: : Local data has changed, and the c
- Page 60 and 61: Figure 4. 5 Drawing in Design Modul
- Page 64 and 65: 22. Edit the details of the slice u
- Page 66 and 67: Figure 4. 15 Details of the Part7.
- Page 68 and 69: Figure 4. 17 Details of the Mesh4.2
- Page 70 and 71: Figure 4. 21 Detials of the Wave Di
- Page 72 and 73: 5. Highlight Diffraction + Froude-K
- Page 74 and 75: Table 4.1 Body Dimensions for Numer
- Page 76 and 77: concavity from concave down to conc
- Page 78 and 79: Figure 4. 29 Maximum Power Absorpti
- Page 80 and 81: Table 4. 3 Numerical ResultsBodyNo.
- Page 82 and 83: BodyNo.Bodyλ atT=2.1λ atT=1.0λ a
- Page 84 and 85: WAVEFigure 5. 1 Body Faces Wave Mak
- Page 86 and 87: The body connects to the aluminum p
- Page 88 and 89: also allowed for flexibility in cre
- Page 90 and 91: AB1 23 4 5 6 7CD8 9 10 11EFigure 5.
- Page 92 and 93: and minimum voltage range of the DA
- Page 94 and 95: Figure 5. 11 Deleting a Step from L
- Page 96 and 97: Figure 5. 14 Recording Options, Sig
- Page 98 and 99: Figure 5. 17 Right-mouse Click on t
- Page 100 and 101: Zero-OffsetThe Zero-Offset step rem
- Page 102 and 103: Figure 5. 24 Filter Step Set-up, Co
- Page 104 and 105: 5.6 Data ProcessingFigure 5. 26 Wav
- Page 106 and 107: 5.8 Experimental DiscussionAs menti
- Page 108 and 109: 5.8.3 Suggestions for Future Resear
- Page 110 and 111: 110ikxxRekddzkgkn )cosh())(cosh(,
12. Delete all lines inside the curve.13. Return to the isometric view by selecting the icon.14. Add the body’s width to the body by selecting the icon.15. Edit the body’s width details under Details of Extrude 1 in the Details View.Set the Direction to Both-Symmetric, and Depth to 2.9375 in. (7.46 cm), asseen in Figure 4.8.Figure 4. 8 Extruding the Body16. After editing the Details of the Extrude 1, select the icon.17. Create a surface rather than a body by selecting the icon.18. Edit the surface details under Details of Thin 1. Set the Selection Type toBodies Only. Set the Thickness to 0 in., as seen in Figure 4.9. Highlight thebody and select Apply under Selection Type.62