Quick Reference for End-Users Lambda Transmitter LT2 ... - lamtec
Quick Reference for End-Users Lambda Transmitter LT2 ... - lamtec Quick Reference for End-Users Lambda Transmitter LT2 ... - lamtec
7 Operation7.2.3 Liquid PurificationYou are allowed to perform a liquid purification of the boiler, when you dismantle the probebeforehand. If you perform a liquid purification to an installed probe, this could damage theprobe. An error free operation is then no longer possibleCAUTION!For the liquid purification, the probe must be dismantled by all means. A liquid purification ofan installed probe will damage the probe.39
8 Service and Maintenance8 Service and MaintenanceIf you want to proceed a liquid purification you must note the following:You may only proceed a liquid purification, if you have dismounted the probe first. If you proceedthe liquid purification without dismounting the probe, this will damage the probe. Theprobe will not function properly after that.CAUTION!You must dismount the probe before liquid purification anyway. Liquid purification without dismountingthe probe will damage the probe.8.1 Checking the O2 Probe8.1.1 Checking the Air VoltageMultifunction key T 2• Switch off the facility• Pre-ventilate, until no more flue gas is present at the measurementsite (approx. 1 minute).• Turn off the pre-ventilation.• Carry out offset calibration either via• the (optional) display and operating unit via "cal” - menu-driven• the (optional) service and diagnostic software• T2 multifunction keyNOTICE!FunctionsToggle the displayed warning/faultReset the displayed warning/faultQuick start of the measuring gas pump - abort ofthe cold startTrigger an offset calibrationHandling of the KeysPress shortlyPress for longer than 3 sec.*Press for longer than 3sec.**Press key for longer than 3 sec.during measurement*** Some warnings and faults cannot be reset if the error is still present or the routine isstill running.**If at least one warning or fault is still present, the key must be pressed for longer than6 seconds.If probe voltage is outside the permissible range, the warning "Offset calibration to air invalid”is output.• Read out probe voltage at LT2either via– the display and operating unit (option)– the service and diagnostic software (option)– measure probe voltage with a multimeter; Connect a digital voltmeter in parallel to the probe at terminal 33 (-) and 34 (+). Compare the measured voltage with the displayed voltage (US).• Valid range: - 0mV … -20 mV• If the probe’s voltage is above/below this range → replace probe40
- Page 1: Quick Reference for End-UsersLambda
- Page 4 and 5: Table of Contents5.3 Wiring Example
- Page 6 and 7: 1 General Information1 General Info
- Page 8 and 9: 2 Safety2.2 For Your Safety2.2.1 Ex
- Page 10 and 11: 2 SafetyUser groupsTwo user groups
- Page 12 and 13: 3 Overview3 Overview3.1 System Over
- Page 14 and 15: 3 Overview3.2 Brief DescriptionUniv
- Page 16 and 17: 4 Technical Description10 LT2 Lambd
- Page 18 and 19: 4 Technical Description4.2.2 Probe
- Page 20 and 21: 4 Technical Description3: Displaya0
- Page 22 and 23: 4 Technical Description12: Analogue
- Page 24 and 25: 4 Technical Description4.5 Options4
- Page 26 and 27: 4 Technical DescriptionMeasurement
- Page 28 and 29: 4 Technical DescriptionDigital outp
- Page 30 and 31: 5 LAMTEC SYSTEM BUS (LSB)5 LAMTEC S
- Page 32 and 33: 6 Commissioning / Shutdown6 Commiss
- Page 34 and 35: 6 Commissioning / Shutdown6.2.3 Int
- Page 36 and 37: 6 Commissioning / ShutdownNOTICE!Re
- Page 38 and 39: 7 Operation7 Operation7.1 Operation
- Page 42 and 43: 8 Service and MaintenanceCAUTION!Do
- Page 44 and 45: 9 Faults / Warnings9 Faults / Warni
- Page 46 and 47: 9 Faults / Warnings9.3.1 Faults - C
- Page 48 and 49: 9 Faults / Warnings9.4.2 Offset Vol
- Page 50 and 51: 11 Appendix11 Appendix11.1 Technica
- Page 52 and 53: 11 AppendixTechnical Data Lambda Tr
- Page 54 and 55: 11 Appendix11.3 Electric Connection
- Page 56 and 57: 11 Appendix11.4 Wet/Dry Measurement
- Page 58 and 59: 12 Declaration of Conformity12 Decl
- Page 60: 12 Declaration of Conformity59
8 Service and Maintenance8 Service and MaintenanceIf you want to proceed a liquid purification you must note the following:You may only proceed a liquid purification, if you have dismounted the probe first. If you proceedthe liquid purification without dismounting the probe, this will damage the probe. Theprobe will not function properly after that.CAUTION!You must dismount the probe be<strong>for</strong>e liquid purification anyway. Liquid purification without dismountingthe probe will damage the probe.8.1 Checking the O2 Probe8.1.1 Checking the Air VoltageMultifunction key T 2• Switch off the facility• Pre-ventilate, until no more flue gas is present at the measurementsite (approx. 1 minute).• Turn off the pre-ventilation.• Carry out offset calibration either via• the (optional) display and operating unit via "cal” - menu-driven• the (optional) service and diagnostic software• T2 multifunction keyNOTICE!FunctionsToggle the displayed warning/faultReset the displayed warning/fault<strong>Quick</strong> start of the measuring gas pump - abort ofthe cold startTrigger an offset calibrationHandling of the KeysPress shortlyPress <strong>for</strong> longer than 3 sec.*Press <strong>for</strong> longer than 3sec.**Press key <strong>for</strong> longer than 3 sec.during measurement*** Some warnings and faults cannot be reset if the error is still present or the routine isstill running.**If at least one warning or fault is still present, the key must be pressed <strong>for</strong> longer than6 seconds.If probe voltage is outside the permissible range, the warning "Offset calibration to air invalid”is output.• Read out probe voltage at <strong>LT2</strong>either via– the display and operating unit (option)– the service and diagnostic software (option)– measure probe voltage with a multimeter; Connect a digital voltmeter in parallel to the probe at terminal 33 (-) and 34 (+). Compare the measured voltage with the displayed voltage (US).• Valid range: - 0mV … -20 mV• If the probe’s voltage is above/below this range → replace probe40