Krohne OPTIFLEX 1300 C Level Meter Quickstart Guide ... - Instrumart

More documents

Recommendations

Info

2 INSTALLATIONOPTIFLEX 1300 C2.10.5 How to install a device with a threaded connectionEquipment needed:• Device• Gasket (not supplied with G (ISO 228) threaded connections)• 50 mm / 2¨ wrench (not supplied)Figure 2-19: Threaded connection• Make sure the tank connection is level.• Make sure that you use the applicable gasket for the connection and the process.• Align the gasket correctly.• If installed on a tank made of plastic or other non-conductive material, refer to Installationrecommendations for non-metallic tanks and pits on page 22.• Lower the probe carefully into the tanki For more data on cable probes, refer to How to install a cable probe in the tank on page 21.• Turn the nut on the housing to attach the device to the process connection• Tighten the nut.i Refer to local rules and regulations for the correct torque to apply to the connection.INFORMATION!If there is not sufficient clearance to install the device, remove the housing. Install the processconnection and then put the housing back on the process connection. For more data, refer toHow to turn or remove the signal converter on page 26.20www.krohne.com09/2010 - 4000049805 - QS OPTIFLEX 1300 R08 en
OPTIFLEX 1300 CINSTALLATION 22.10.6 How to install a cable probe in the tankFigure 2-20: Wind cable probes and flexible conduits carefully1 Do not wind cable probes less than 400 mm / 16¨ in diameter.2 Do not wind the flexible conduit less than 330 mm / 13¨ in diameter.WARNING!If you bend the probe too much, you will damage the device and it will not measure accurately.Figure 2-21: Installation of devices with cable probes1 >1 m / 3½ ft• Use two persons to lift the housing and the probe above the process connection.• Hold the device 1 m / 3½ ft above the tank.• Unwind the probe carefully into the tank.09/2010 - 4000049805 - QS OPTIFLEX 1300 R08 enwww.krohne.com21
Page 1 and 2: OPTIFLEX 1300 C Quick StartGuided R
Page 3 and 4: OPTIFLEX 1300 CCONTENTS4 Start-up 3
Page 5 and 6: OPTIFLEX 1300 CINSTALLATION 22.1 In
Page 7 and 8: OPTIFLEX 1300 CINSTALLATION 22.3 Vi
Page 9 and 10: OPTIFLEX 1300 CINSTALLATION 22.5 Tr
Page 11 and 12: OPTIFLEX 1300 CINSTALLATION 2Temper
Page 13 and 14: OPTIFLEX 1300 CINSTALLATION 21 23 3
Page 15 and 16: OPTIFLEX 1300 CINSTALLATION 2INFORM
Page 17 and 18: OPTIFLEX 1300 CINSTALLATION 2Figure
Page 19: OPTIFLEX 1300 CINSTALLATION 22.10.4
Page 23 and 24: OPTIFLEX 1300 CINSTALLATION 22.10.8
Page 25 and 26: OPTIFLEX 1300 CINSTALLATION 2You ca
Page 27 and 28: OPTIFLEX 1300 CINSTALLATION 22.10.1
Page 29 and 30: OPTIFLEX 1300 CINSTALLATION 22.11 E
Page 31 and 32: OPTIFLEX 1300 CELECTRICAL CONNECTIO
Page 33 and 34: OPTIFLEX 1300 CSTART-UP 44.1 Start-
Page 35 and 36: OPTIFLEX 1300 CSTART-UP 44.3.4 How
Page 37 and 38: OPTIFLEX 1300 CTECHNICAL DATA 55.1
Page 39 and 40: OPTIFLEX 1300 CTECHNICAL DATA 5Othe
Page 41 and 42: OPTIFLEX 1300 CTECHNICAL DATA 5Reso
Page 43 and 44: OPTIFLEX 1300 CTECHNICAL DATA 55.2

Krohne OPTIFLEX 1300 C Level Meter Quickstart Guide ... - Instrumart

Create successful ePaper yourself

Delete template?

Save as template?