Alexandria X-2 Series 2 - Wilson Audio

More documents

Recommendations

Info

A l e x a n d r i a X - 2 S e r i e s 2 O w n e r ’ s M a n u a land heads.The front-to-back location of each module, along with the use of the proper lengthof rear spike of the upper modules, achieves the correct propagation delay and axial responsevis a vis the listener.Install the front pair of short (A length) spikes into the bottom of each module (seeFigure 15).Install the Lower Midrange Module (LMRM)The lower midrange module (LMRM) is installed first. Install the module as follows:• With the front spikes pointing down, carefully lower the LMRM betweenthe alignment wings and set it on top of the woofer enclosure (see Figure16). Ensure that the tether bolts are protruding through the slots providedin the module handle. There are alignment tracks that accommodate thespikes. Refer to the Propagation Delay Table to determine the numberedindent in which to rest the rear spike.• It is now safe to install the rear spike by lifting the module by its rear handleand carefully screwing in the spike.• The rear spike track is indexed numerically. Refer to your marks on thePropagation Delay Table in Section 8.0 to determine the numbered detentin which to rest the rear spike.Install the High Frequency Module (HFM) as follows:• With the front pair of short spikes pointing down, carefully lower the HFMbetween the alignment wings and set the front two spikes on top of theLMRM enclosure. Align the spikes into the alignment tracks. Install the rearspike by lifting the rear of the HFM and carefully screwing it in.• Refer to the Propagation Delay Table in Section 8 to determine the properlocation of the rear spike, noting that the position will be different from theLMRM.52Wilson Audio Specialties
S e c t i o n 4 . 4 – C o n n e c t i n g t h e U p p e r M o d u l e s ’ S i g n a l C a b l eInstall the Upper Midrange Module(UMRM) as follows:• With the front pair ofshort spikes pointingdown, carefully lowerthe UMRM between thealignment wings. Set thefront two spikes on topof the HFM enclosure,into the tracks. Installthe rear spike by liftingthe rear of the UMRMand carefully screwing itin.• Refer to the PropagationDelay Table in Section 8to determine the properlocation of the rear spike,noting that the positionwill be different from theother two modules.Section 4.4 – Connecting theUpper Modules’ Signal CableThe Alexandria uses binding poststhat were designed in-house and aremanufactured exclusively for WilsonAudio. The design goal was to create aconnector with superior overall soundquality, consistency, and longevity.Figure 16 - Install the upper modules into the wingarray.Wilson Audio Specialties53
Page 7 and 8: Wilson Audio Specialties7
Page 9: Section 1 - Introduction
Page 12 and 13: A l e x a n d r i a X - 2 S e r i e
Page 14: A l e x a n d r i a X - 2 S e r i e
Page 17 and 18: Section 2 - In Your Room
Page 19: S e c t i o n 2 . 1 - R o o m A c o
Page 22: A l e x a n d r i a X - 2 S e r i e
Page 32 and 33: Wilson Audio Specialties
Page 47: S e c t i o n 4 . 1 - I n i t i a l
Page 80 and 81: 80Wilson Audio Specialties
Page 98 and 99: Wilson Audio Specialties
Page 102 and 103:
A l e x a n d r i a X - 2 S e r i e
Page 104:
A l e x a n d r i a X - 2 S e r i e
show all

Alexandria X-2 Series 2 - Wilson Audio

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?