TERCERA â¢ Owner's Manual - Del Mar Fans and Lighting

More documents

Recommendations

Info

OPERATION CFL MODEYour fan has the ability to disable 1 the 2dimming feature to allow the use ofCFL bulbs.0To activate CFL mode:4 31. Turn the fan off by pressing thepower button.2. Allow the fan to remain off for at least 5 seconds.3. Press the power button again to restore power to the fan.4. Immediately press and hold 1 the "1" 2 and "3" buttons for at least 5 seconds. The fans lights will go to100% brightness and the dimming 0 function will be disabled.To cancel CFL mode:4 35. Turn the fan off by pressing thepower button.6. Allow the fan to remain off for at least 5 seconds.7. Press the power button again to restore power to the fan.CHANGING FREQUENCY SETTINGCaution: CFL bulbs will notfunction properly whendimmed, which may resultin flickering or reduced bulblife.8. Immediately press and hold the "2" and "4" buttons for at least 5 seconds. The fans lights will dim to50% brightness and the dimming function will be enabled. Press and hold the light buttons until thedesired dimmer setting is reached.NOTE: All fans leave the factory set to“111111”DIPSWITCHESYou will only have to change the dip switch settings in the remote if youare using more than one fan in the same area and want to control themseparately.NOTE: DO NOT set dip switch setting in theremote to ‘0000’, this may cause frequencyinterference from other Casablanca Products.DIP SWITCHESSET TO ‘111111’(Factory Setting)(Figure 1)1. Turn power OFF at the circuit breaker or fuse box and at the toggleswitch, for the fan you want to change.2. Remove the screws and switch plate from the existing switch box.3. Remove the screws holding the switch in the switch box.4. Pull the existing W-74 switch from the switch box to expose the dipswitches located on the side of the control as shown in Figure #1.5. Change the dip switch settings, assuring that they are different fromthe previously installed Direct-Touch fan.6. Mount the W-74 Wall Control unit back into the wall 1 electrical 2 box.7. At the circuit breaker or fuse box and at the toggle switch, 0 turn thepower off for the fan whose frequency you are 4changing.38. Within 20 seconds of restoring power to the ceiling fan and the W-74Wall Control press and hold both the “1” and reverse buttonsas shown in Figure #2. For 3 seconds, you will hear one tone fromthe Piezo Buzzer indicating the command has been accepted. The Fanand Lights will be off.20DIP SWITCHESSET TO ‘000000’(Figure 2)
Direct - TouchAUTOMATIC DEMONSTRATION PROGRAMProgrammed into every Direct-Touch fan is an Automatic DemonstrationProgram. 1 It can 2 be used to fully demonstrate and test the operation of thefan. 041 32To enter the demonstration program:01. Turn the power button off for at least 5 seconds. This will clear4 3the fan memory ready for programming.2. Turn thepower button on.3. Immediately hold the "0" button for at least 5 seconds.A multi-tone signal will verify the start of the test program. The fan and1 2lights will go through a series of changing fan speeds, reversing the fanoperation mode, 0 turning off/on, and dimming the lights.4 3The complete cycle lasts slightly over one minute. It will continue torepeat until the is turned off for more than five seconds, cancellingthe program.1 2OPERATION SAFE-EXIT®The Safe-Exit 0 Program gives you about thirty seconds of light when you turn thelights off, 4 enabling 3 you to exit your home before the lights go out. To enter the Safe-Exit Program:1. Press the power button off for at least five seconds.Safe-Exit2. Turn the Power on. Immediately press and hold the "4" button for 5 seconds.When a light button is pressed, an audio tone and series of lights blinking will indicate the program1 2is active. When CFL mode is disabled, the Lights will stay on at 50% brightness for 20 seconds thendecrease in intensity for 30 seconds then 0turn off.4 33. With CFL mode active, the lights will turn off after 30 seconds.4. To cancel the Safe-Exit Program, press the1 2The Light-Minder Program automatically turns OFF the fan mounted 0 lights after twohours. To 1 enter 2the Light-Minder Program:4 301. To operate the lights for Light Minder Program – Turn the4 3for at least 5 seconds.power button off2. Turn the on. Immediately press and hold the "1" button for 5 seconds. Aseries of tones will be heard through the piezo-buzzer indicating the commandhas been accepted. Once the lights turn on, they will automatically turn off after2 hours.Light-Minder3. Light operation still remains normal, if you 1 leave 2the room and turn OFF thelights, the lights will blink to indicate the Light 0 Minder command has beenaccepted. The lights will stay on for 2 hours and then begin to dim. After thirty seconds have elapsed,4 3the lights will turn completely off. In CFL Mode, the lights will not dim, but shut off after 2 hours.4. To cancel the Light Minder Program, press thepower button and leave off for five seconds.LIGHT-MINDER® PROGRAMNote: With CFL mode active,the lights will not dim.power button and leave off for five seconds.21
Page 2: Parts ListParts List242526255122042
Page 11: WIRING HARDWARETercera Receiver Blu
Page 14 and 15: BLADE HARDWAREScrew DriverBlades (3
Page 16 and 17: W-74 WALL CONTROL PREPARATIONWARNIN
Page 18 and 19: DUAL W-74 INSTALLATIONTo control th
Page 22 and 23: 1 21 201. To operate the Home-Safe
Page 24: Fan Finishes• For cleaning, a sof

TERCERA â¢ Owner's Manual - Del Mar Fans and Lighting

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

TERCERA â¢ Owner's Manual - Del Mar Fans and Lighting