TERCERA ⢠Owner's Manual - Del Mar Fans and Lighting
TERCERA ⢠Owner's Manual - Del Mar Fans and Lighting TERCERA ⢠Owner's Manual - Del Mar Fans and Lighting
BLADE HARDWAREScrew DriverBlades (3) Grommets (9) Blade Screws (9)Blade Washers (9)Step 1. Locate the blade slot on the side of the fanas shown in Figure 1., and insert the blade into theslot.BLADE INSTALLATIONBlade SlotBladeStep 2. Align the holes in the blade with the holeson the fan as shown in Figure 2.FIGURE 1.Step 3. Insert the Blade Screws into the Washersthen Grommets.Step 4. Insert the Blade Screw, Washer, andGrommet through the blade and screw into thefan using either the provided Screw Driver or astandard Phillips head. Once all 3 Screws andGrommets have been installed, tighten securely.CAUTION:Blade screws must be tightened securelybefore operating the fan.Step 5. Repeat steps 3 and 4 for the remaining twoblades.14FIGURE 2.FIGURE 3.
LIGHT HARDWARETercera E11 50W Halogen BulbLIGHT INSTALLATIONGlass AssemblyStep 1. Install both Halogen Bulbs into the LightKit. Figure 1.Note: When replacing bulbs, only replace with max50 watt bulbs.IMPORTANT ! When installing the halogen bulb,carefully cut off the end of the plastic sleeve thebulb comes in and hold the bulb by the plasticsleeve to screw it into the socket.FIGURE 1.Step 2. Position the indentations in the outer rim ofthe glass shade so that they line up with the tabs onthe inside surface of the fan light fixture rim.Step 3. Carefully lift the glass shade up inside thelight fixture as far as it will go. Figure 2.FIGURE 2.Step 4. Rotate the shade in a clockwise directionuntil it is held tightly in place by the four tabs. Figure3.FIGURE 3.15
- Page 2: Parts ListParts List242526255122042
- Page 11: WIRING HARDWARETercera Receiver Blu
- Page 16 and 17: W-74 WALL CONTROL PREPARATIONWARNIN
- Page 18 and 19: DUAL W-74 INSTALLATIONTo control th
- Page 20 and 21: OPERATION CFL MODEYour fan has the
- Page 22 and 23: 1 21 201. To operate the Home-Safe
- Page 24: Fan Finishes• For cleaning, a sof
BLADE HARDWAREScrew DriverBlades (3) Grommets (9) Blade Screws (9)Blade Washers (9)Step 1. Locate the blade slot on the side of the fanas shown in Figure 1., <strong>and</strong> insert the blade into theslot.BLADE INSTALLATIONBlade SlotBladeStep 2. Align the holes in the blade with the holeson the fan as shown in Figure 2.FIGURE 1.Step 3. Insert the Blade Screws into the Washersthen Grommets.Step 4. Insert the Blade Screw, Washer, <strong>and</strong>Grommet through the blade <strong>and</strong> screw into thefan using either the provided Screw Driver or ast<strong>and</strong>ard Phillips head. Once all 3 Screws <strong>and</strong>Grommets have been installed, tighten securely.CAUTION:Blade screws must be tightened securelybefore operating the fan.Step 5. Repeat steps 3 <strong>and</strong> 4 for the remaining twoblades.14FIGURE 2.FIGURE 3.
Change language