SWS - Stemco Quick Reference 2011 - CARQUEST Auto Parts

More documents

Recommendations

Info

Voyager ® / Discover ® / Endeavor ® InstallationHUB SEAL INSTALLATIONSTEP 1Remove all burrs from hub bore and spindle.Thoroughly clean hub cavity and spindle.NOTE: Do not apply a sealant to the spindleshoulder. Apply a light coat of lubricant tospindle surfaces.STEP 2With the wheelin horizontalposition, prelubethe innerbearing andplace it into thebearing cup.NOTE: When using grease, pre-pack theinner bearing before placement into the hub.STEP 3Place the seal onthe recommendedSTEMCO InstallationTool, with thecorrect head, so thatthe words “Air Side”face into the tool.Place the tool (withthe seal correctlymounted in the toolhead) over the hubbore. Use a heavyhammer to driveagainst the end of the tool. Drive seal intobore until complete bottoming is assured.Remove Tool. Apply a thin layer of lubricant onthe I.D. surface of the seal.NOTE: Do not apply lubricant to the O.D.of the seal.STEP 4With the wheelmounted on adolly, carefullyalign the borewith the spindle.Gently push thewheel assemblyonto the spindleto the proper position. Fill the hub cavity withlubricant until it runs over the outer bearingcup. Coat the outer bearing with lubricant andplace it on the spindle and into the bearingcup. NOTE: When using grease, pre-pack theouter bearing before placement into the hub.NOTE: Support the hub with the lifting deviceuntil the outer bearing and wheel-end fastenerhave been installed to a hand tight condition toprevent cocking of the hub/seal.STEP 5Assemble theinner nut andtighten it to200 ft. lbs.Rotate thewheel severaltimes thenback off nut one full turn. Make final bearingadjustment according to TMC recommendedbearing adjustment procedure. Install theappropriate axle fastener.STEP 6Install hub cap with new gasket, and fill cavitywith the desired lubricant to the proper level.On drive axles be sure the differential oil is highenough (manufacturer’s recommended level) toensure oil flow through the tube to the wheels.It is recommended to jack one side up andthen the other until flow starts. Make certainthe breather plug is clear. Recheck steers andtrailers to ensure proper fill levels.52 Order Entry 1-800-527-8492 Fax 1-800-874-4297 <strong>2011</strong>
Unitized Pinion Seal InstallationSTEP 1Remove yoke.STEP 2Remove old sealand wear ring(if applicable).STEP 3Remove allburrs andthoroughlyclean cagebore.NOTE: If installingthe seal into a worn cage bore, apply a thin layer ofNo. 2 sealant to the OD of the seal before installation.STEP 4Aligninstallationtool withthe seal andsplineas shown.Hand tightenbolt/nut.STEP 5Tighten untilthe seal flangebottoms intothe cage -orinstallationtoolbottoms intocage (nonflangeseals).Take care not to overtighten bolt/nut.STEP 6Remove burrsand thoroughlyclean yoke.Lube the sealID. Install yokeas shown.STEP 7Refer to axlemanufacturerfor yokeassemblytorquerequirements.PINION SEAL INSTALLATION<strong>2011</strong> Order Entry 1-800-527-8492 Fax 1-800-874-4297 53
Page 1 and 2:
Q U I C K RE F E R E N C EPART NUMB
Page 3 and 4: PlatinumPerformance System Flexible
Page 6 and 7: GUARDIAN® HP Application Reference
Page 8 and 9: High Performance…Revolutionary De
Page 10 and 11: ®High Performance…Revolutionary
Page 12 and 13: ®Voyager ® Cross Reference GuideV
Page 14 and 15: GRIT GUARD® Application Reference
Page 16 and 17: SKF to STEMCOSKFGUARDIAN ® HP GRIT
Page 18 and 19: Standard and Grit Guard ® Hub Seal
Page 20 and 21: Standard and Grit Guard ® Hub Seal
Page 22 and 23: HEAVY DUTYBEARINGSValue Added Beari
Page 24 and 25: Bearings to Hub Seal Set Cross Refe
Page 26 and 27: PINION SEAL SPECIFICATIONSPinion Se
Page 28 and 29: ®SENTINEL ® TECHNOLOGYProvides an
Page 30 and 31: Hub Cap SpecificationsHub Caps By C
Page 32 and 33: Hub Cap SpecificationsSentinel ® H
Page 34 and 35: Hub Cap SpecificationsStamped Steel
Page 36 and 37: Hub Cap SpecificationsBlank Hub Cap
Page 38 and 39: Hub Cap SpecificationsPopular Hub C
Page 40 and 41: ®AN INDISPENSABLE TOOL FOR…• S
Page 42 and 43: GUARANTEED ACCURACYCONSTRUCTION AND
Page 44 and 45: Longer Tread LifeFleets save tires,
Page 46 and 47: PRO-TORQ ® APPLICATIONS & SPECSPro
Page 48 and 49: High Performance Brake LiningsThe v
Page 50 and 51: Private Label Reference20,000 lb. A
Page 52 and 53: Standard/Grit Guard ® Seal Install
Page 56 and 57: BEARING ADJUSTMENTPro-Torq® Instal
Page 58 and 59: Wheel Bearing AdjustmentWHEEL BEARI
Page 60 and 61: NOTESNotes58 Order Entry 1-800-527-
Page 62 and 63: NOTESNotes60 Order Entry 1-800-527-
Page 64: STEMCO QUALITY PRODUCTSHEAVY DUTYBE
show all

SWS - Stemco Quick Reference 2011 - CARQUEST Auto Parts

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?