Base Station Antenna Systems 2008 Product Selection Guide - AVW

Teletilt ® Remote Electrical Downtilt SystemControl CablesCable AssembliesPart Number Description Length, m (ft)ATCB-B01-C50 Cable assembly 0.5 (1.6)ATCB-B01-001 Cable assembly 1 (3.3)ATCB-B01-002 Cable assembly 2 (6.6)ATCB-B01-003 Cable assembly 3 (9.8)ATCB-B01-004 Cable assembly 4 (13.1)ATCB-B01-005 Cable assembly 5 (16.4)ATCB-B01-006 Cable assembly 6 (19.7)ATCB-B01-009 Cable assembly 9 (29.5)ATCB-B01-010 Cable assembly 10 (32.8)ATCB-B01-015 Cable assembly 15 (49.2)ATCB-B01-020 Cable assembly 20 (65.6)ATCB-B01-030 Cable assembly 30 (98.4)ATCB-B01-040 Cable assembly 40 (131.2)ATCB-B01-050 Cable assembly 50 (164.0)ATCB-B01-060 Cable assembly 60 (196.9)ElectricalRatings:300 V (max.)EU certification:CE, CBEnvironmental: ETSI EN 300 019-2-2, 2-3, & 2-4;NEBS GR 63 core issue 2 2002zone 4 earthquake; NEBS GR 63core issue 2 2002 § 5.1, 5.2, 5.3, 5.4,5.5, 5.6, & 5.7Cable Kit AssembliesPart Number Description Length, m (ft)ATCB-B01-070K ATCB-B01-030 (1) 70 (229.7)and ATCB-B01-040 (1)cables, plus ATGK-001grounding kitATCB-B01-080K ATCB-B01-040 (2) 80 (262.5)cables, plus ATGK-001grounding kitATCB-B01-090K ATCB-B01-040 (1) 90 (295.3)and ATCB-B01-050 (1)cables, plus ATGK-001grounding kitATCB-B01-100K ATCB-B01-050 (2) 100 (328.1)cables, plus ATGK-001grounding kitCable and ConnectorsCable spec:4 x 0.75mm² (20 AWG) stranded (power)2 x 0.25mm² (24 AWG) twisted pair (data)6 conductor cable, 6.6mm (0.26") diameterScreen:~85% coverage, braid-type shieldConnectors/interfaces: Terminated with AISG 8-pin socketscrew lock, IP67 male and female DINMechanical/EnvironmentalStandard length, m: .5, 1.0, 2.0, 3.0, 4.0, 5.0, 6.0, 9.0,10.0, 15.0, 20.0, 30.0, 40.0, 50.0, 60.0Jacket:Flame retardant, PolyeurthaneTemperature range: –40° C to +70° CHumidity: Up to 100%IP rating:IP67, mated and unmatedAll specifications are subject to change. Please see www.andrew.com for the most current information.Notes:1. The main control cable, feeding to the tower structure, should be secured at 2m intervals and 1m from either end usingcableties (Andrew 40417), hangers (Andrew 68MCLICK), or similar fasteners. Control cabling feeding between junction boxesand actuators should be secured every 0.5m to avoid excessive wind vibration.2. Connectors should only be hand tightened. Over tightening can shear pins off internal components of equipment.3. Connectors do not require waterproofing.4. Maximum distance from control unit to farthest AISG component in a RET system should not exceed 200m.Andrew Wireless Solutions www.andrew.com75