70/140H-8 Series (2310KB) - TAIYO
70/140H-8 Series (2310KB) - TAIYO
70/140H-8 Series (2310KB) - TAIYO
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
75<br />
General purpose hydraulic cylinder<br />
<strong>70</strong>/<strong>140H</strong>-8<br />
MM<br />
CS<br />
<strong>70</strong>H-8 0 1 CS Bore B B Stroke – A B<br />
<strong>140H</strong>-8 1 CS Bore B B Stroke – A B<br />
B<br />
KK<br />
S<br />
With boots<br />
φWW<br />
Rod B • C<br />
Nylon tarpaulin<br />
Chloroprene<br />
Conex<br />
VD<br />
A W FP PJ + stroke<br />
SL<br />
2-EE<br />
● The grease is not sealed at the shipment.<br />
⎞ ⎟⎟⎠<br />
W<br />
φ40 • φ50 1/ 3.5 Stroke + X<br />
φ63 - φ100 1/4 Stroke + X<br />
φ200 1/5 Stroke + X<br />
⎞ ⎟⎟⎠<br />
φ40 • φ50 1/2.5 Stroke + X<br />
φ63 - φ100 1/3 Stroke + X<br />
φ125 1/3.5 Stroke + X<br />
7/14 MPa double acting hydraulic cylinder<br />
Double acting single rod/double rod Unit: mm<br />
Cushion valve<br />
HL + stroke<br />
XD + stroke<br />
ZC + stroke<br />
⎞<br />
⎟<br />
⎠<br />
⎞<br />
⎟<br />
⎠<br />
Material<br />
Resistible<br />
temperature<br />
Standard<br />
Nylon tarpaulin<br />
80°C<br />
<strong>70</strong>-<strong>140H</strong>-8/TH8 Bore K<br />
Semi-standard<br />
Chloroprene<br />
130°C<br />
Conex<br />
200°C<br />
Notes) ● Remember that the resistible temperatures shown in the table above are for the<br />
boots, not for the cylinder.<br />
● Conex is the registered trademark of Teijin Ltd.<br />
● If decimals are included into the calculation results, raise them to the next whole<br />
number.<br />
● The boots have been mounted at our factory prior to delivery.<br />
Rod A<br />
Nylon tarpaulin<br />
Chloroprene<br />
Conex<br />
φ40 - φ100 :Max. 7<br />
φ125 :Max. 11<br />
grease nipple<br />
● Inner diameter and installation width of bearing are conformed to JIS B8367-2 MP5 type regulation. (Same<br />
standard with 160H-1 series.)<br />
● For the dimensions other than in the diagram above, refer to the specification of the SD type (standard<br />
type).<br />
● For the mounting of switches, refer to the dimensional drawings of “Switch set”. All the contents other than<br />
“Switch mounting dimensions” are identical.<br />
L<br />
FL<br />
EL<br />
⎞ ⎟⎟⎠<br />
φ40 1/ 3.5 Stroke + X<br />
φ50 - φ80 1/4 Stroke + X<br />
φ100 • φ125 1/5 Stroke + X<br />
φ40 1/2.5 Stroke + X<br />
φ50 - φ80 1/3 Stroke + X<br />
φ100 1/3.5 Stroke + X<br />
φ125 1/4 Stroke + X<br />
⎞ ⎟⎟⎟⎠<br />
CD<br />
MR<br />
E<br />
EN<br />
EM<br />
⎞<br />
⎟<br />
⎠<br />
⎞<br />
⎟<br />
⎠<br />
3˚<br />
3˚<br />
MAX.HG
Change language