REFERENCE MANUAL - J&H Licht en Geluid

More documents

Recommendations

Info

10. Set all faders and knobs to the middle/center position. The left Deck’s HOT CUE BUTTON 1 will light up.11. Press the lit left Deck’s HOT CUE BUTTON 1. The left Deck’s HOT CUE BUTTONS 1-5 will flash, indicating that calibration iscomplete.12. Turn the NS7’s power off then on again before reconnecting it to your computer.28
TROUBLESHOOTINGPROBLEM CAUSE SOLUTIONThe USB cable is not properly connected Make sure both USB connections areto your computer or NS7.secure.I'm seeing a “Hardware Disconnected”The software was opened before NS7 was Close the software and reopen aftermessage in the software.connected.properly connecting and powering onNS7 not powered on.NS7.Close any unnecessary programs andturn off your computer’s wireless card (ordisconnect from the internet).Disable anti-virus software or otherprograms that regularly scan yourcomputer or regularly search for aninternet connection.Change the buffer size settings in theI’m experiencing some audio dropouts or Other programs are draining yoursoftware (see "USB Buffer Size" on Pageslow response.computer’s CPU.12). At a larger buffer size, you should nolonger experience audio dropouts, butthere may be a slight delay when thesoftware responds to the hardware(latency). At a lower buffer size, yourcomputer will respond more quickly (lesslatency), but your computer needs to befast enough to prevent audio dropouts orother issues. Experiment to find theoptimal settings for your computer.Software closes or freezes as soon as itopens.I’m having problems scanning orsearching through my iTunes library.I’m hearing a weird noise when I startplayback if the NS7’s PLATTER isstopped.I'm experiencing software problems whenrunning my finger along the NS7's STRIPSEARCH.The auto-BPM reading for a track isincorrect.iTunes 8.0.2 (and higher) is interfering withhow the software scans its libraries.The PLATTER’s start time is too high.The STRIP SEARCH sensor isn't meant toreceive information in a “continuous”fashion (i.e., running your finger across it).The software’s BPM Range is not properlyset for your track's tempo. (The BPMRange is restricting what BPMs areallowed.)Your track's rhythm is very syncopated orhas bass drum or snare drum hits in oddplaces, causing a BPM miscalculation.Downgrade your version of iTunes athttp://www.oldapps.com/itunes.htm.Decrease the PLATTER’s start time byadjusting the START TIME knob. (See"PLAYBACK CONTROLS" on Page 7.)Only use the STRIP SEARCH as if youwere dropping a needle on a record –touch it at only one point at a time. Toscroll/scrub through the track, spin thePLATTER instead.With the NS7 disconnected, set thesoftware's BPM Range to an appropriaterange that will allow the BPMs you want,then rebuild the overview for that track.(See "Auto-BPM" on Page 10.)Manually tap a tempo for the track bypressing the Deck’s TAP button (on theNS7) in time with the track.For more information, visit:http://www.numark.com/ns7http://www.serato.com/itch29
Page 5 and 6: INTRODUCTIONWelcome to NS7 - a prof
Page 7 and 8: SOFTWARE INSTALLATIONNote: Install
Page 9 and 10: REAR PANEL OVERVIEW2 4 61 351. USB
Page 11 and 12: TRANSPORT CONTROLSUSEFUL TERMS:•
Page 13 and 14: USING SERATO ITCH WITH THE NS7GETTI
Page 15 and 16: SOFTWARE OVERVIEWMore complete desc
Page 17 and 18: ON SONG LOAD: These options affect
Page 19 and 20: Clicking Browse in the software wil
Page 21 and 22: MIXING WITH THE NS7PLAYING YOUR FIR
Page 23 and 24: • Main WaveformsThis view provide
Page 25 and 26: USING PITCH / TEMPO CONTROLSThe fol
Page 27 and 28: Serato ITCH can capture recordings
Page 29 and 30: UPDATING THE FIRMWAREThis section t
Page 31: 6. Set all faders and knobs to the
Page 36: www.numark.com

REFERENCE MANUAL - J&H Licht en Geluid

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?