Pneumatic cylinders - Duncan Rogers

More documents

Recommendations

Info

P1DCylinderP1D CleanP1D Clean is a new version in our ISO cylinder system,completely designed for the foodstuffs industry. Manyyears’ experience of the stringent requirements forhygiene, choice of material and corrosion resistance,from a wide spectrum of foodstuffs applications haveguided the development of this cylinder version. Greatemphasis has been put on the external design of thecylinder, choice of materials and corrosion protection.Main dimensions according to international standardsAll the main dimensions of the P1D Clean comply withISO 6431, ISO 15552, VDMA 24562 and AFNOR standards.The exception is the somewhat larger footprint ofthe end covers and envelope of the body extrusion, dueto the so-called positive geometry (hygienic, convex,easy-to-clean geometry) of the cushioning adjustmentscrew and the components in the integrated sensorsystem.Common, high technology design platformThe P1D Clean has the same technical platform asthe P1D Standard. The best materials, including thepolyurethane (PUR) seals, manufacturing methods andthe careful attention to detail design give the P1D Cleansmooth, quiet operation and long service life.Convex shape for optimum hygieneP1D Clean has a convex body extrusion, which makesthe <strong>cylinders</strong> easy to keep clean. Irrespective of installationposition, fluids run off the body extrusion surfaces.06.05www.parker.com/euro_pneumatic
P1DCylinderCushioning screw with positive geometryTo offer the best hygiene properties, the projecting cushioningscrew, is sealed with rubber seal against the endcover. This eliminates dirt-collecting cavities and givesthe best hygiene, since it is so easy to clean.Sealing plugsFour plastic sealing plugs are supplied with everyP1D Clean cylinder. These are installed in the end coverscrews which are not used for the cylinder installation. Toensure the sealing function, the plugs can be used onlyonce i.e. they can not be re-used. When installed in theend cover screws, they should be tapped lightly with ahammer to securely fix.Patent applied system for integrated standard sensorsThe P1D Clean cylinder has a system of sensors, whichare fully integrated into the body extrusion, to give the<strong>cylinders</strong> a clean external design. Up to four sensorschosen from the range of P1D standard sensors, reed orelectronic operation, can be mounted in two dedicatedgrooves beneath a transparent, sealed moulding.Tightening the stop screw onto the cam shaft, will lockeach sensor in the desired position, with great force. Thesensor LEDs are always fully visible, which facilitatescommissioning, adjustment and trouble-shooting. Theentire sensor system has a hose-proof design, equivalentto IP65. P1D Clean can be ordered with factoryfittedsensors in the end positions, which can then easilybe moved to any other position along the entire stroke.Up to four integral sensorsCylinders for two integral sensors have two undividedcamshafts along the entire stroke. Free choice of cableexit, front or rear. There is also a version with dividedcamshafts for up to four sensors, which are installed twofrom each end cover, with cable exit front and rear.Simple sensor adjustmentThe sensors are mounted into their groovesthrough the opening in a transparent, sealedcover. The sensor cables have strain reliefand are sealed.The sensor position is easily adjusted byundoing a set screw and using the cable tomove the sensor to the desired position.Once the sensor has been locked in its newposition, the protective cover is installedagain.06.05www.parker.com/euro_pneumatic
Page 1 and 2: Pneumatic cylindersSeries P1DAccord
Page 3 and 4: P1DCylinderContentspageISO cylinder
Page 5 and 6: P1DCylinderThe same high technology
Page 7: P1DCylinderComplete accessory progr
Page 11 and 12: P1DCylinderStraight or elbow push-i
Page 13 and 14: P1DCylinderDesign variants for P1D
Page 15 and 16: P1DCylinderDesign variants for P1D
Page 17 and 18: P1DCylinderCylinder forces, double
Page 19 and 20: P1DMaterial specificationStandard d
Page 21: P1DExample 1 : Which tube diameter
Page 24 and 25: P1DCylinderSafety instructions for
Page 26 and 27: P1DStandard cylinderP1D StandardCAD
Page 28 and 29: P1DThe simple and complete order ke
Page 30 and 31: P1DCylinderP1D cylinders with pisto
Page 32 and 33: P1DCylinderFactory-fitted sensorsAl
Page 34 and 35: P1DCylinderExtended piston rodAll c
Page 36 and 37: P1DCylinderThrough piston rodAll P1
Page 38 and 39: P1DP1D Clean with built-in sensorTh
Page 40 and 41: P1DCylinderP1D CleanThe order numbe
Page 42 and 43: P1DCylinderP1D Flexible PortingThe
Page 44 and 45: P1DCylinderCombine P1D Clean and P1
Page 46 and 47: P1DTechnical dataWorking pressurema
Page 48 and 49: P1DPiston rod lockingP1D-LP1D-DP1D
Page 50 and 51: P1DFastening in positionPiston rod
Page 52 and 53: P1DRod Guidance ModulesAluminium bo
Page 54 and 55: P1DRod Guidance ModulesL1 + SA1B1B4
Page 56 and 57: IP1DMountingsCylinder mountingsType
Page 58 and 59:
P1DMountingsCylinder mountingsType
Page 60 and 61:
P1DMountingsCylinder mountingsType
Page 62 and 63:
P1DMountingsPiston rod mountingsTyp
Page 64 and 65:
P1DMountingsCombinationsType Descri
Page 66 and 67:
P1DMountingsCombinationsType and de
Page 68 and 69:
P1DSensorsElectronic sensorsReed se
Page 70 and 71:
P1DSensorsConnecting cables with on
Page 72 and 73:
P1DSensorsPneumatic cylinder sensor
Page 74 and 75:
P1DSeal kitsP1D Seal kitsComplete s
Page 76 and 77:
P1DSpare PartsOrder key, spare part
Page 78 and 79:
P1DOrder code keyThere is a P1D cyl
Page 80 and 81:
P1DOrder code keyCylinder versionS
Page 82:
P1DOrder code keyInformation notes1
show all

Pneumatic cylinders - Duncan Rogers

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?