Pneumatic cylinders - Duncan Rogers

P1DCylinderP1D Flexible PortingThe P1D Flexible Porting with both cylinder ports in one endcover has a 20-digit part number. Position 11 is used to selectthe position of the cylinder ports (all cylinders with one connectionin each end cover have a dash in this position). Pleasenote that cylinder bores 32-63 mm only have the push-in fittingdesign and 80-125 mm is only available with threaded connections.Position 20 is used to specify the type of push-in fittings(low elbow or straight fitting) and tube dimension (4 or 6 mmfor Ø32 and 40, and 8 or 10 mm for Ø50 and 63). For cylinderbores Ø32-63 mm, the fittings are made of plastics material forFlexible Porting cylinders (nickel plated brass on all other P1Dcylinders). These four smallest bores can not be equipped withspeed controls. For cylinder bores Ø80-125 mm, position 20is used to select the speed controls, fittings (Prestolok, nickelplated brass) or none (code N).1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20P 1 D – F 0 6 3 M S B 0 3 2 0 N N N N 0Cylinder versionS StandardC CleanF Flexible PortingT Tie-RodCylinder portsFront & rearBoth frontBoth rearH 3) J 3)3) Only for P1D-F bore 80-125 mm. Select optionalfittings in position 20.4) Only for P1D-F bore 32-63 mm. Select fittingsin position 20.16) P1D Clean cylinders have factory installednickel plated versions of the PTF series.17) Not available for P1D Flexible Portingbore 32-63 mm.Port locationG threads, BSPP (Ø80-125 mm)– B 4) C 4) Push-in , metric (Ø32-63 mm)Available fittings and speed controls for P1D Flexible PortingCyl. Speed controls Elbow fitting Straight fittingbore for tube for tube for tube32, 40 not available 4, 6 4, 650, 63 not available 8, 10 8, 1080 8, 10, 12 8, 10, 12 8, 10, 12100, 125 12 12 10, 12Speed controls orfittings for tube dimensionSpeed controls 17)Series PTF4PB 16)X in both ends for tube 4 mmY in both ends for tube 6 mmZ in both ends for tube 8 mmP in both ends for tube 10 mmR in both ends for tube 12 mmPush-in fitting, elbow type for:4 Tube dimension 4 mm6 Tube dimension 6 mm8 Tube dimension 8 mm0 Tube dimension 10 mm2 Tube dimension 12 mmPush-in fitting, straight type for:1 Tube dimension 4 mm3 Tube dimension 6 mm5 Tube dimension 8 mm7 Tube dimension 10 mm9 Tube dimension 12 mmN NoneExamples of P1D Flexible PortingP1D-F050MSB0160SMKN8 Flexible Porting cylinder with two plug-in low elbow fittings for 8 mm tube, placed at front end cover, zinc plated steelswivel rod eye, combination clevis bracket GA and swivel eye bracket installed on rear end cover,two factory-fitted reed sensors with 3 m cable.P1D-F080MSH0500BFCNFlexible Porting cylinder with two threaded connections in front end cover, zinc plated steel clevis, foot brackets, twofactory-fitted electronic sensors, PNP type, with 8 mm connector (0.3 m cable), sealing plugs installed in unused endcover screws.P1D-F032MSB0250NNNN6 Flexible Porting cylinder with two push-in elbow fittings for 6 mm tube, placed at front end cover.P1D-F063MSC0400NNNN7 Flexible Porting cylinder with two straight push-in fittings for 10 mm tube, placed at rear end cover(only possible to choose 8 or 10 mm for cylinder bore 50 and 63 mm).P1D-F125MSJ0600NNNNN Flexible Porting cylinder with two threaded connections in rear end cover.06.0542www.parker.com/euro_pneumatic