Pneumatic cylinders - Duncan Rogers

More documents

Recommendations

Info

P1DCylinderP1D Tie-RodThe P1D is available in a tie-rod version, based on thesame high level technology. This future-proof cylinder isthe perfect choice wherever a tie-rod cylinder is needed.Installation dimensions to international standardThe P1D Tie-Rod complies with ISO 6431, ISO 15552,VDMA 24562 and AFNOR installation dimension standards.For customer reassurance world-wide.Smooth, quiet operation and long service lifeAll seals and end-of-stroke washers are made frompolyurethane (PUR), the bearings and piston are madefrom proven engineering plastics with excellent bearingproperties and the initial greasing at the factory with atransparent, foodstuffs-approved grease. Altogether thisgives the P1D very long service life and gentle, quietoperation.Optimised cushioningThanks to the plastic inserts in the end covers, eachcylinder bore has been given an individual flow geometry.This gives an optimised cushioning, which isquicker and easier to set and adjust.Complete accessory programmeP1D offers a complete ISO, VDMA and AFNOR compatibleaccessory programme, with a wide range of pistonrod and cylinder mountings for both pivoted and fixedoperation.”Drop-in” sensorThe P1D Tie-Rod uses ”drop-in” P1D sensors. Aningenious multi-jointed adapter fixes the sensors in anychosen position along the stroke.1206.05www.parker.com/euro_pneumatic
P1DCylinderDesign variants for P1D Standard, P1D Clean, P1D Flexible porting and P1D Tie-RodUsing P1D cylinders as a platform, a number of differentdesigns can be produced to suit differing requirements. Pleaserefer to the order key on pages 28 - 51 for the designation ofeach variant.P1D complete working unitP1D Standard can be ordered with a factory-fitted valve andpiping. The valve series is the robust and compact Vikingseries.Of course, the entire range of P1D accessories can also beused for the P1D with built-in valve, and cylinders can beordered with factory-fitted accessories and sensors.For more information, see page 45.P1D-LP1D cylinder with piston rod lockingThe P1D cylinder is available in a version with piston rodlocking, allowing the piston rod to be locked in any position.The lock unit, of the air/spring actuated type, is integrated inthe front end piece of the cylinder. The lock unit can be usedfor braking as well as locking. With no signal pressure, the fullforce of the lock is applied to the piston rod, and the lock isreleased at 4 bar signal pressure. Lock units are available forP1D Standard(P1D-L) and P1D Clean (P1D-D) in dimensions Ø32-125 mm.P1D Standard can be ordered with a lock unit and a built-invalve (P1D-4).For more information, see page 48P1D-DP1D cylinder with internal piston rod threadAll P1D cylinders are available with an internal piston rodthread where a short installation length is required1306.05www.parker.com/euro_pneumatic
Page 1 and 2: Pneumatic cylindersSeries P1DAccord
Page 3 and 4: P1DCylinderContentspageISO cylinder
Page 5 and 6: P1DCylinderThe same high technology
Page 7 and 8: P1DCylinderComplete accessory progr
Page 9 and 10: P1DCylinderCushioning screw with po
Page 11: P1DCylinderStraight or elbow push-i
Page 15 and 16: P1DCylinderDesign variants for P1D
Page 17 and 18: P1DCylinderCylinder forces, double
Page 19 and 20: P1DMaterial specificationStandard d
Page 21: P1DExample 1 : Which tube diameter
Page 24 and 25: P1DCylinderSafety instructions for
Page 26 and 27: P1DStandard cylinderP1D StandardCAD
Page 28 and 29: P1DThe simple and complete order ke
Page 30 and 31: P1DCylinderP1D cylinders with pisto
Page 32 and 33: P1DCylinderFactory-fitted sensorsAl
Page 34 and 35: P1DCylinderExtended piston rodAll c
Page 36 and 37: P1DCylinderThrough piston rodAll P1
Page 38 and 39: P1DP1D Clean with built-in sensorTh
Page 40 and 41: P1DCylinderP1D CleanThe order numbe
Page 42 and 43: P1DCylinderP1D Flexible PortingThe
Page 44 and 45: P1DCylinderCombine P1D Clean and P1
Page 46 and 47: P1DTechnical dataWorking pressurema
Page 48 and 49: P1DPiston rod lockingP1D-LP1D-DP1D
Page 50 and 51: P1DFastening in positionPiston rod
Page 52 and 53: P1DRod Guidance ModulesAluminium bo
Page 54 and 55: P1DRod Guidance ModulesL1 + SA1B1B4
Page 56 and 57: IP1DMountingsCylinder mountingsType
Page 58 and 59: P1DMountingsCylinder mountingsType
Page 60 and 61: P1DMountingsCylinder mountingsType
Page 62 and 63:
P1DMountingsPiston rod mountingsTyp
Page 64 and 65:
P1DMountingsCombinationsType Descri
Page 66 and 67:
P1DMountingsCombinationsType and de
Page 68 and 69:
P1DSensorsElectronic sensorsReed se
Page 70 and 71:
P1DSensorsConnecting cables with on
Page 72 and 73:
P1DSensorsPneumatic cylinder sensor
Page 74 and 75:
P1DSeal kitsP1D Seal kitsComplete s
Page 76 and 77:
P1DSpare PartsOrder key, spare part
Page 78 and 79:
P1DOrder code keyThere is a P1D cyl
Page 80 and 81:
P1DOrder code keyCylinder versionS
Page 82:
P1DOrder code keyInformation notes1
show all

Pneumatic cylinders - Duncan Rogers

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?