Owner's Manual - Roland

MIDI Implementation3. Data reception (Sequencer Section)3.1 Messages recorded during recording■Channel Voice Messages●Note OffStatus 2nd byte 3rd byte8nH kkH vvH9nH kkH 00Hn=MIDI channel number:0H - FH (ch.1 - ch.16)kk=note number: 00H - 7FH (0 - 127)vv=note off velocity: 00H - 7FH (0 - 127)* Not received when the Note parameter (Recording Select window) is OFF.●Note onStatus 2nd byte 3rd byte9nH kkH vvHn=MIDI channel number:0H - FH (ch.1 - ch.16)kk=note number: 00H - 7FH (0 - 127)vv=note on velocity: 01H - 7FH (1 - 127)* Not received when the Note parameter (Recording Select window) is OFF.●Polyphonic AftertouchStatus 2nd byte 3rd byteAnH kkH vvHn=MIDI channel number:0H - FH (ch.1 - ch.16)kk=note number: 00H - 7FH (0 - 127)vv=Polyphonic Aftertouch: 00H - 7FH (0 - 127)* Not received when the Poly Afertouch parameter (Recording Select window) is OFF.●Control ChangeStatus 2nd byte 3rd byteBnH kkH vvHn=MIDI channel number:0H - FH (ch.1 - ch.16)kk=Control number: 00H - 78H (0 - 120)vv=value: 00H - 7FH (0 - 127)* Not received when the Control Change parameter (Recording Select window) is OFF.■Channel Mode messages●All Sound Off (Controller number 120)Status 2nd byte 3rd byteBnH 78H 00Hn=MIDI channel number:0H - FH (ch.1 - ch.16)●Reset All Controller (Controller number 121)Status 2nd byte 3rd byteBnH 79H 00Hn=MIDI channel number:0H - FH (ch.1 - ch.16)●Omni Off (Controller number 124)Status 2nd byte 3rd byteBnH 7CH 00Hn=MIDI channel number:0H - FH (ch.1 - ch.16)* The same processing will be done as when an All Note Off message is received.●Omni On (Controller number 125)Status 2nd byte 3rd byteBnH 7DH 00Hn=MIDI channel number:0H - FH (ch.1 - ch.16)* The same processing will be done as when an All Note Off message is received.●Mono (Controller number 126)Status 2nd byte 3rd byteBnH 7EH mmHn=MIDI channel number:0H - FH (ch.1 - ch.16)mm=mono number: 00H - 10H (0 - 16)* The same processing will be done as when an All Note Off message is received.●Poly (Controller number 127)Status 2nd byte 3rd byteBnH 7FH 00Hn=MIDI channel number:0H - FH (ch.1 - ch.16)* The same processing will be done as when an All Note Off message is received.●Program ChangeStatus2nd byteCnHppHn=MIDI channel number:pp=Program number:0H - FH (ch.1 - ch.16)00H - 7FH (prog.1 - prog.128)* Not received when the Program Change parameter (Recording Select window) is OFF.●Channel AftertouchStatus2nd byteDnHvvHn=MIDI channel number:0H - FH (ch.1 - ch.16)vv=Channel Aftertouch: 00H - 7FH (0 - 127)* Not received when the Channel Aftertouch parameter (Recording Select window) isOFF.●Pitch Bend ChangeStatus 2nd byte 3rd byteEnH llH mmHn=MIDI channel number:0H - FH (ch.1 - ch.16)mm, ll=Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)* Not received when the Pitch Bend parameter (Recording Select window) is OFF.307