Owner's Manual - Roland

More documents

Recommendations

Info

MIDI Implementation1. Receive Data (Sound Source Section)■Channel Voice Messages* Not received in Performance mode when the Receive Switch parameter (PERFORM/MIDI) is OFF.●Note offStatus 2nd byte 3rd byte8nH kkH vvH9nH kkH 00Hn = MIDI channel number: 0H - FH (ch.1 - 16)kk = note number: 00H - 7FH (0 - 127)vv = note off velocity: 00H - 7FH (0 - 127)* Not received when the Envelope Mode parameter (PATCH/MISC and RHYTHM/GENERAL) is NO-SUS.●Note onStatus 2nd byte 3rd byte9nH kkH vvHn = MIDI channel number: 0H - FH (ch.1 - 16)kk = note number: 00H - 7FH (0 - 127)vv = note on velocity: 01H - 7FH (1 - 127)●Polyphonic Key PressureStatus 2nd byte 3rd byteAnH kkH vvHn = MIDI channel number: 0H - FH (ch.1 - 16)kk = note number: 00H - 7FH (0 - 127)vv = Polyphonic Key Pressure: 00H - 7FH (0 - 127)* Not received in Performance mode when the Receive Poly Key Pressure parameter(PERFORM/MIDI) is OFF.●Control Change* If the corresponding Controller number is selected for the Patch Control Source 1, 2, 3 or4 parameter (PATCH/CTRL1-4), the corresponding effect will occur.* If a Controller number that corresponds to the System Control Source 1, 2, 3 or 4parameter (SYSTEM/SYSTEM CONTROL) is selected, the specified effect will apply ifPatch Control Source 1, 2, 3 or 4 parameter (PATCH/CTRL1–4) is set to SYS-CTRL1,SYS-CTRL2, SYS-CTRL3 or SYS-CTRL4.❍Bank Select (Controller number 0, 32)Status 2nd byte 3rd byteBnH 00H mmHBnH 20H llHn = MIDI channel number: 0H - FH (ch.1 - 16)mm, ll = Bank number: 00 00H - 7F 7FH (bank.1 - bank.16384)* Not received in Performance mode when the Receive Bank Select (PERFORM/MIDI) isOFF.* The Performances, Patches, and Rhythms corresponding to each Bank Select are asfollows.* The SRX series corresponding to each Bank Select are to see the SRX series owner’smanual.BANK SELECT | PROGRAM | GROUP | NUMBERMSB | LSB | NUMBER | |-----+-----------+-----------+----------------------+-----------000 | | 001 - 128 | GM Patch | 001 - 256: | | | |063 | | 001 - 128 | GM Patch | 001 - 256085 | 000 | 001 - 064 | User Performance | 001 - 064| 032 | 001 - 064 | Card Performance | 001 - 064| 064 | 001 - 064 | Preset Performance | 001 - 064086 | 000 | 001 - 032 | User Rhythm | 001 - 032| 032 | 001 - 032 | Card Rhythm | 001 - 032| 064 | 001 - 032 | Preset Rhythm | 001 - 032087 | 000 | 001 - 128 | User Patch | 001 - 128| 001 | 001 - 128 | User Patch | 129 - 256| 032 | 001 - 128 | Card Patch | 001 - 128| 033 | 001 - 128 | Card Patch | 129 - 256| 064 | 001 - 128 | Preset Patch A | 001 - 128| 065 | 001 - 128 | Preset Patch B | 001 - 128| : | | : |092 | 000 - | 001 - | SRX Rhythm | 001 -| : | | : |093 | 000 - | 001 - | SRX Patch | 001 -| : | | : |120 | | 001 - 057 | GM Rhythm | 001 - 009121 | 000 - | 001 - 128 | GM Patch | 001 - 256❍Modulation (Controller number 1)Status 2nd byte 3rd byteBnH 01H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Modulation depth: 00H - 7FH (0 - 127)* Not received in Performance mode when the Receive Modulation parameter(PERFORM/MIDI) is OFF.❍Breath type (Controller number 2)Status 2nd byte 3rd byteBnH 02H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Control value: 00H - 7FH (0 - 127)❍Foot type (Controller number 4)Status 2nd byte 3rd byteBnH 04H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Control value: 00H - 7FH (0 - 127)❍Portamento Time (Controller number 5)Status 2nd byte 3rd byteBnH 05H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Portamento Time: 00H - 7FH (0 - 127)* In Performance mode the Part Portament Time parameter (PERFORM/PART) willchange.❍Data Entry (Controller number 6, 38)Status 2nd byte 3rd byteBnH 06H mmHBnH 26H llHn = MIDI channel number: 0H - FH (ch.1 - 16)mm, ll = the value of the parameter specified by RPN/NRPNmm = MSB, ll = LSB❍Volume (Controller number 7)Status 2nd byte 3rd byteBnH 07H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Volume: 00H - 7FH (0 - 127)* Not received in Performance mode when the Receive Volume parameter (PERFORM/MIDI) is OFF.* In Performance mode the Part Level parameter (PERFORM/PART) will change.❍Balance (Controller number 8)Status 2nd byte 3rd byteBnH 08H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Balance: 00H - 7FH (0 - 127)❍Panpot (Controller number 10)Status 2nd byte 3rd byteBnH 0AH vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Panpot:00H - 40H - 7FH (Left - Center - Right),* Not received in Performance mode when the Receive Pan parameter (PERFORM/MIDI)is OFF.* In Performance mode the Part Pan parameter (PERFORM/PART) will change.❍Expression (Controller number 11)Status 2nd byte 3rd byteBnH 0BH vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Expression: 00H - 7FH (0 - 127)* Not received when Tone Receive Expression parameter (PATCH/MISC or RHYTHM/GENERAL) is OFF.* Not received in Performance mode when Receive Expression parameter (PERFORM/MIDI) is OFF.298
MIDI Implementation❍Hold 1 (Controller number 64)Status 2nd byte 3rd byteBnH 40H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Control value:00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON* Not received when Tone Receive Hold-1 parameter (PATCH/MISC or RHYTHM/GENERAL) is OFF.* Not received in Performance mode when Receive Hold-1 parameter (PERFORM/MIDI)is OFF.* When the Tone Redamper Switch parameter (PATCH/CONTROL) is turned ON, 128discrete steps are recognized for the value.❍Portamento (Controller number 65)Status 2nd byte 3rd byteBnH 41H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Control value:00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON* In Performance mode the Part Portamento Switch parameter (PERFORM/PART) willchange.❍Sostenuto (Controller number 66)Status 2nd byte 3rd byteBnH 42H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Control value:00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON❍Soft (Controller number 67)Status 2nd byte 3rd byteBnH 43H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Control value:00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON❍Legato Foot Switch (Controller number 68)Status 2nd byte 3rd byteBnH 44H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Control value:00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON* In Performance mode the Part Legato Switch parameter (PERFORM/PART) will change.❍Hold-2 (Controller number 69)Status 2nd byte 3rd byteBnH 45H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Control value: 00H - 7FH (0 - 127)* A hold movement isn’t done.❍Resonance (Controller number 71)Status 2nd byte 3rd byteBnH 47H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv= Resonance value (relative change): 00H - 40H - 7FH (-64 - 0 - +63),* In Performance mode the Part Resonance Offset parameter (PERFORM/PART) willchange.❍Release Time (Controller number 72)Status 2nd byte 3rd byteBnH 48H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Release Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63),* In Performance mode the Part Release Time Offset parameter (PERFORM/PART) willchange.❍Attack time (Controller number 73)Status 2nd byte 3rd byteBnH 49H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Attack time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63),* In Performance mode the Part Attack Time Offset parameter (PERFORM/PART) willchange.❍Cutoff (Controller number 74)Status 2nd byte 3rd byteBnH 4AH vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Cutoff value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)* In Performance mode the Part Cutoff Offset parameter (PERFORM/PART) will change.❍Decay Time (Controller number 75)Status 2nd byte 3rd byteBnH 4BH vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Decay Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)* In Performance mode the Part Decay Time Offset parameter (PERFORM/PART) willchange.❍Vibrato Rate (Controller number 76)Status 2nd byte 3rd byteBnH 4CH vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Vibrato Rate value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)* In Performance mode the Part Vibrato Rate parameter (PERFORM/PART) will change.❍Vibrato Depth (Controller number 77)Status 2nd byte 3rd byteBnH 4DH vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Vibrato Depth Value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)* In Performance mode the Part Vibrato Depth parameter (PERFORM/PART) will change.❍Vibrato Delay (Controller number 78)Status 2nd byte 3rd byteBnH 4EH vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Vibrato Delay value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)* In Performance mode the Part Vibrato Delay parameter (PERFORM/PART) will change.❍General Purpose Controller 5 (Controller number 80)Status 2nd byte 3rd byteBnH 50H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Control value: 00H - 7FH (0 - 127)* The Tone Level parameter (PATCH/TVA) of Tone 1 will change.❍General Purpose Controller 6 (Controller number 81)Status 2nd byte 3rd byteBnH 51H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Control value: 00H - 7FH (0 - 127)* The Tone Level parameter (PATCH/TVA) of Tone 2 will change.❍General Purpose Controller 7 (Controller number 82)Status 2nd byte 3rd byteBnH 52H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Control value: 00H - 7FH (0 - 127)* The Tone Level parameter (PATCH/TVA) of Tone 3 will change.❍General Purpose Controller 8 (Controller number 83)Status 2nd byte 3rd byteBnH 53H vvHn = MIDI channel number: 0H - FH (ch.1 - 16)vv = Control value: 00H - 7FH (0 - 127)* The Tone Level parameter (PATCH/TVA) of Tone 4 will change.299
Page 1 and 2:
Owner’s ManualThank you, and cong
Page 3 and 4:
USING THE UNIT SAFELYUsed for instr
Page 5 and 6:
IMPORTANT NOTESMaintenance401a• F
Page 7 and 8:
ContentsPlaying in Patch Mode .....
Page 9 and 10:
ContentsCreating a Performance ....
Page 11 and 12:
ContentsUsing the Pads.............
Page 13 and 14:
ContentsMaking Reverb Settings (Rev
Page 15 and 16:
Main FeaturesCutting-edge sound eng
Page 17 and 18:
Panel Descriptions[STOP]Controls se
Page 19 and 20:
Getting ReadyConnecting an Amp and
Page 21 and 22:
Getting ReadyTurning On the PowerOn
Page 23 and 24:
Listening to the Demo SongsThe Fant
Page 25 and 26:
Various Performance FeaturesControl
Page 27 and 28:
Overview of the Fantom-XLFO (Low Fr
Page 29 and 30:
Overview of the Fantom-XTemporary M
Page 31 and 32:
Overview of the Fantom-XTempo Track
Page 33 and 34:
Overview of the Fantom-XBasic Opera
Page 35 and 36:
Overview of the Fantom-XModifying a
Page 37 and 38:
Overview of the Fantom-XRegistering
Page 39 and 40:
Playing in Patch ModeFunctions in t
Page 41 and 42:
Playing in Patch ModeThe following
Page 43 and 44:
Playing in Patch ModeRegistering a
Page 45 and 46:
Playing in Patch ModeRegistering Fa
Page 47 and 48:
Playing in Patch ModeCreating Smoot
Page 49 and 50:
Playing in Patch ModeD Beam (Solo S
Page 51 and 52:
Playing in Patch ModeKnobfig.05-021
Page 53 and 54:
Playing in Patch ModePlaying a Rhyt
Page 55 and 56:
Playing in Piano Mode2. Use the VAL
Page 57 and 58:
Creating a Patch8. Repeat steps 5-7
Page 59 and 60:
Creating a PatchCautions When Using
Page 61 and 62:
Creating a PatchPatch CategorySpeci
Page 63 and 64:
Creating a PatchWave Gain1FXM Color
Page 65 and 66:
Creating a PatchBooster 1&2, 3&4 (B
Page 67 and 68:
Creating a PatchModifying Pitch (Pi
Page 69 and 70:
Creating a PatchModifying the Brigh
Page 71 and 72:
Creating a PatchTVF ENVF-Env Depth
Page 73 and 74:
Creating a PatchA-Env T4 V-Sens (TV
Page 75 and 76:
Creating a PatchRate Detune (LFO1/L
Page 77 and 78:
Creating a PatchApply Portamento or
Page 79 and 80:
Creating a PatchOFF-N:fig.06-053.eR
Page 81 and 82:
Creating a PatchMatrix Control 1-4
Page 83 and 84:
Creating a Rhythm SetWith the Fanto
Page 85 and 86:
Creating a Rhythm Set3. Press [F5 (
Page 87 and 88:
Creating a Rhythm Set4. If you wish
Page 89 and 90:
Creating a Rhythm SetWave No. L (Mo
Page 91 and 92:
Creating a Rhythm SetPitchTone Coar
Page 93 and 94:
Creating a Rhythm SetCutoff V-Sens
Page 95 and 96:
Creating a Rhythm SetA-Env Level 1-
Page 97 and 98:
Playing in Performance ModeA perfor
Page 99 and 100:
Playing in Performance ModeSelectin
Page 101 and 102:
Page 103 and 104:
Playing in Performance ModeUsing th
Page 105 and 106:
Page 107 and 108:
Creating a PerformanceWith the Fant
Page 109 and 110:
Creating a Performance[F3 (Pitch)]f
Page 111 and 112:
Creating a PerformanceKeyboard Rang
Page 113 and 114:
Creating a PerformanceExt Pan (Exte
Page 115 and 116:
Creating a PerformanceD Beam (Solo
Page 117 and 118:
Creating a PerformanceKnobfig.09-01
Page 119 and 120:
Creating a PerformanceControl D Bea
Page 121 and 122:
Modifying the Sound in Real TimeYou
Page 123 and 124:
Modifying the Sound in Real TimePad
Page 125 and 126:
Modifying the Sound in Real TimeCha
Page 127 and 128:
Modifying the Sound in Real Time127
Page 129 and 130:
Playing Arpeggios1. Connect an opti
Page 131 and 132:
Playing ArpeggiosHanging the Range
Page 133 and 134:
Using the Chord Memory Function (Ch
Page 135 and 136:
Playing RhythmsAbout Rhythm Pattern
Page 137 and 138:
Playing RhythmsChanging the Beat an
Page 139 and 140:
Playing RhythmsSaving the Patterns
Page 141 and 142:
SamplingThe Fantom-X lets you sampl
Page 143 and 144:
Sampling• Re-Sampling: [F2 (Re-Sa
Page 145 and 146:
SamplingSampling Earlier in Time(Sk
Page 147 and 148:
Editing a SampleLoading a SampleHer
Page 149 and 150:
Editing a SampleSetting the Start/E
Page 151 and 152:
Editing a SampleAssigning Samples t
Page 153 and 154:
Editing a Sample3. Press [F7 (Load
Page 155 and 156:
Editing a Sample6. When you’ve fi
Page 157 and 158:
Editing a Sample3. Press [F5 (Time
Page 159 and 160:
Editing a Sample4. Either turn the
Page 161 and 162:
Using the PadsMaking Settings for t
Page 163 and 164:
Using the PadsAssigning a Pattern t
Page 165 and 166:
Playing Back a Song4. Press [PLAY]
Page 167 and 168:
Playing Back a SongUsing the D Beam
Page 169 and 170:
Recording SongsSpecify the Time Sig
Page 171 and 172:
Recording SongsRecording Tempo Chan
Page 173 and 174:
Recording Songs4. Turn the VALUE di
Page 175 and 176:
Recording Songs• Step BackCancel
Page 177 and 178:
Editing SongsThis chapter explains
Page 179 and 180:
Editing Songs3. Turn the VALUE dial
Page 181 and 182:
Editing SongsAligning a Song’s Ti
Page 183 and 184:
Editing SongsRange Min, Range MaxSp
Page 185 and 186:
Editing SongsStatusSelects the type
Page 187 and 188:
Editing SongsMeasure, For (Edit Ran
Page 189 and 190:
Editing SongsExtract ModeSpecifies
Page 191 and 192:
Editing SongsStatusSelects the type
Page 193 and 194:
Editing Songs5. When you are finish
Page 195 and 196:
Editing SongsErasing Sequencer Data
Page 197 and 198:
Editing SongsAssigning a Name to aS
Page 199 and 200:
Saving/Loading a song (Save/Load)Sa
Page 201 and 202:
Saving/Loading a song (Save/Load)If
Page 203 and 204:
Playing a Phrase at the Touch of a
Page 205 and 206:
Playing a Phrase at the Touch of a
Page 207 and 208:
Adding EffectsApplying Effects in P
Page 209 and 210:
Adding Effects13Chorus Output Selec
Page 211 and 212:
Adding Effects6Part Reverb Send Lev
Page 213 and 214:
Adding EffectsMaking Multi-EffectsS
Page 215 and 216:
Adding EffectsSpecifying the multi-
Page 217 and 218:
Adding EffectsMastering EffectThis
Page 219 and 220:
Connecting to Your Computer via USB
Page 221 and 222:
Connecting to Your Computer via USB
Page 223 and 224:
File-Related Functions (File Utilit
Page 225 and 226:
Settings Common to All Modes (Syste
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Data Management FunctionsReset to D
Page 237 and 238:
Using Fantom-X EditorFantom-X Edito
Page 239 and 240:
About V-LINKV-LINK ParametersNote T
Page 241 and 242:
Installing the Wave Expansion Board
Page 243 and 244:
Installation de la carte d’expans
Page 245 and 246:
Expanding the Memory4. Paying atten
Page 247 and 248: Ajouter de la mémoire4. Prenez bie
Page 249 and 250: TroubleshootingIf the Fantom-X does
Page 251 and 252: TroubleshootingIssues Related to Ef
Page 253 and 254: Troubleshooting• Is the data conc
Page 255 and 256: Parameter ListPatch ParameterGenera
Page 257 and 258: Parameter ListTVA Env Group (P.72)P
Page 259 and 260: Parameter ListRhythm Set ParameterG
Page 261 and 262: Parameter ListEffect Group (P.207)P
Page 263 and 264: Parameter ListParameterValue[F8 (MI
Page 265 and 266: Parameter ListRhythm Group Paramete
Page 267 and 268: Parameter ListMIDI Group (P.230)Par
Page 269 and 270: Parameter ListV-LINK Group (P.239)P
Page 271 and 272: Effects List01: EQUALIZERThis is a
Page 273 and 274: Effects List08: AUTO WAHCyclically
Page 275 and 276: Effects List15: RING MODULATORThis
Page 277 and 278: Effects List23: CHORUSThis is a ste
Page 279 and 280: Effects List30: 3D FLANGERThis appl
Page 281 and 282: Effects List35: OVERDRIVECreates a
Page 283 and 284: Effects List44: LONG DELAYA delay t
Page 285 and 286: Effects ListParameter Range Explana
Page 287 and 288: Effects List57: LOFI COMPRESSThis i
Page 289 and 290: Effects ListParameter Value Descrip
Page 291 and 292: Effects List74: ENHANCER → DELAYf
Page 293 and 294: Effects ListAbout the STEP RESET fu
Page 295 and 296: Effects List05: NOISE SUPPRESSORSup
Page 297: About MIDIMIDI (Musical Instruments
Page 301 and 302: MIDI Implementation■Channel Mode
Page 303 and 304: MIDI Implementation❍Channel Press
Page 305 and 306: MIDI Implementation❍Volume (Contr
Page 307 and 308: MIDI Implementation3. Data receptio
Page 309 and 310: MIDI Implementation■System Realti
Page 311 and 312: MIDI Implementation5. Parameter Add
Page 313 and 314: MIDI Implementation| 00 06 | 0000 0
Page 315 and 316: MIDI Implementation| | 0000 cccc |
Page 317 and 318: MIDI Implementation|# 00 54 | 0000
Page 319 and 320: MIDI Implementation| | | USER, PRES
Page 321 and 322: MIDI Implementation| | | -20000 - +
Page 323 and 324: MIDI Implementation|—————
Page 325 and 326: MIDI Implementation| | 0000 dddd |
Page 327 and 328: MIDI Implementation| | | -64 - +63
Page 329 and 330: MIDI Implementation■Example of an
Page 331 and 332: (Sound Generator Section)Model Fant
Page 333 and 334: SpecificationsFantom-X6/X7/X8:Synth
Page 335 and 336: IndexSymbols+OCT/-OCT .............
Page 337 and 338: IndexDeletingDividing Point .......
Page 339 and 340: IndexMMagnify .....................
Page 341 and 342: IndexP-Env DepthPatch .............
Page 343 and 344: IndexSolo/Portamento ..............
Page 345 and 346: IndexVoice Reserve ................
Page 347 and 348: Model Name :Type of Equipment :Resp
show all

Owner's Manual - Roland

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?