Owner's Manual - Roland

Effects ListReverb ParametersThese settings allow you to select the desired type of reverb, and itscharacteristics.Parameter Value DescriptionReverbType0 (OFF),1 (REVERB),2 (SRV ROOM),3 (SRV HALL),4 (SRV PLATE),5 (GM2 REVERB)Type: 1 (REVERB)Type ROOM1,ROOM2,STAGE1,STAGE2,HALL1, HALL2,DELAY,PAN-DELAYType of reverb0 (OFF): Reverb is not used.1 (REVERB): Normal reverb2 (SRV ROOM): This simulates typicalroom acoustic reflections.3 (SRV HALL): This simulates typical concerthall acoustic reflections.4 (SRV PLATE): This simulates a reverbplate, a popular type of artificial reverbunit that derives its sound from the vibrationof a metallic plate.5 (GM2 REVERB): GM2 ReverbType of reverb/delayROOM1: short reverb with high densityROOM2: short reverb with low densitySTAGE1: reverb with greater late reverberationSTAGE2: reverb with strong early reflectionsHALL1: very clear-sounding reverbHALL2: rich reverbDELAY: conventional delay effectPAN-DELAY: delay effect with echoesthat pan left and rightTime 0–127 Time length of reverberation(Type: ROOM1–HALL2)Delay time(Type: DELAY, PAN-DELAY)HF Damp200–8000 Hz,BYPASSAdjusts the frequency above which the highfrequencycontent of the reverb sound will becut, or “damped.” If you do not want to cut thehigh frequencies, set this parameter to BYPASS.DelayFeedback0–127 Adjusts the amount of delay feedback whenthe Type setting is DELAY or PAN-DELAY.Type: 2 (SRV ROOM)/3 (SRV HALL)/4 (SRV PLATE)PreDelay0.0–100.0 ms Adjusts the delay time from the direct sounduntil the reverb sound is heard.Time 0–127 Time length of reverberationSize 1–8 Size of the simulated room or hallHigh Cut 160 Hz–12.5 kHz,BYPASSAdjusts the frequency above which the highfrequencycontent of the reverb will be reduced.If you do not want to reduce the highfrequencies, set this parameter to BYPASS.Density 0–127 Density of reverbDiffusion 0–127 Adjusts the change in the density of the reverbover time. The higher the value, the more the densityincreases with time. (The effect of this settingis most pronounced with long reverb times.)LF DampFreqLF DampGainHF DampFreqHF DampGain50–4000 Hz Adjusts the frequency below which the lowfrequencycontent of the reverb sound will bereduced, or “damped.”-36–0 dB Adjusts the amount of damping applied tothe frequency range selected with LF Damp.With a setting of “0,” there will be no reductionof the reverb’s low-frequency content.4000 Hz–12.5 kHz Adjusts the frequency above which the highfrequencycontent of the reverb sound will bereduced, or “damped.”-36–0 dB Adjusts the amount of damping applied tothe frequency range selected with HF Damp.With a setting of “0,” there will be no reductionof the reverb’s high-frequency content.Type: 5 (GM2 REVERB)Character 0–7 Type of reverb0–5: reverb6, 7: delayPre-LPF 0–7 Cuts the high frequency range of the soundcoming into the reverb.Higher values will cut more of the highfrequencies.Level 0–127 Output level of reverbrationTime 0–127 Time length of reverberationDelayFeedback0–127 Adjusts the amount of the delay sound that isfed back into the effect when the ReverbCharacter setting is 6 or 7.Input Effect ParametersSelects the type of effect that will be applied to the external inputsource.01: EQUALIZERAdjusts the tone of the low-frequency and high-frequency ranges.Parameter Range ExplanationLow Freq 200, 400 Hz Center frequency of the low-frequencyrangeLow Gain -15–+15 dB Amount of low-frequencyboost/cutHigh Freq 2000, 4000, 8000 Hz Center frequency of the highfrequencyrangeHigh Gain -15–+15 dB Amount of high-frequencyboost/cut02: ENHANCERModifies the harmonic content of the high-frequency range to addsparkle to the sound.Parameter Range ExplanationSens 0–127 Depth of the enhancer effectMix 0–127 Volume of the harmonics thatare generated03: COMPRESSORRestrains high levels and boosts low levels to make the overallvolume more consistent.Parameter Range ExplanationAttack 0–127 Time from when the input exceedsthe Threshold until thevolume begins to be compressedThreshold 0–127 Volume level at which compressionwill beginPost Gain 0–+18 dB Level of the output sound04: LIMITERCompresses the sound when it exceeds a specified volume, to keepdistortion from occurring.Parameter Range ExplanationRelease 0–127 Time from when the input fallsbelow the Threshold until compressionceasesThreshold 0–127 Volume level at which compressionwill beginPost Gain 0–+18 dB Level of the output sound294