Owner's Manual - Roland

Effects ListAbout the STEP RESET function06: STEP FILTER16: STEP RING MODULATOR19: STEP PAN20: SLICER63: STEP PITCH SHIFTERThe above five types contain a sixteen-step sequencer.For these types, you can use a multi-effect control to reset thesequence to play from the first step.To do this, set the multi-effect control Destination to “StepReset.”For example if you are using the modulation lever to control theeffect, you would make the following settings.Source: CC01: MODULATIONDestination: Step ResetSens: +63With these settings, the sequence will play back from the firststep whenever you operate the modulation lever.note:fig.MFX-note2.e_88(Sixty-fourth-note triplet), (Sixty-fourth note), (Thirty-second-note triplet),(Thirty-second note), (Sixteenth-note triplet), (Dotted thirty-second note),(Sixteenth note), (Eighth-note triplet), (Dotted sixteenth note),(Eighth note), (Quarter-note triplet), (Dotted eighth note),(Quarter note), (Half-note triplet), (Dotted quarter note), (Half note),(Whole-note triplet), (Dotted half note), (Whole note),(Double-note triplet), (Dotted whole note), (Double note)Chorus ParametersThe Fantom-X’s Chorus effect unit can also be used as a stereo delayunit.These settings allow you to select chorus or delay, and thecharacteristics of the selected effect type.Parameter Value DescriptionChorusTypefig.MFX-note2.e0 (OFF),1 (CHORUS),2 (DELAY),3 (GM2 CHORUS)Selects either Chorus or Delay.0 (OFF): Neither Chorus or Delayis used.1 (CHORUS): Chorus is used.2 (DELAY): Delay is used.3 (GM2 CHORUS): GM2 Chorusis used.Delay RightDelay CenterCenterFeedbackType: 1 (CHORUS)Rate 0.05–10.00 Hz, note Frequency of modulationDepth 0–127 Depth of modulationPre Delay 0.0–100.0 ms Adjusts the delay time from the directsound until the chorus sound is heard.Feedback 0–127 Adjusts the amount of the chorussound that is fed back into the effect.Filter Type OFF, LPF, HPF Type of filterOFF: no filter is usedLPF: cuts the frequency rangeabove the Cutoff FreqHPF: cuts the frequency rangebelow the Cutoff FreqCutoff Freq 200–8000 Hz Basic frequency of the filterPhase 0–180˚ Spatial spread of the soundType: 2 (DELAY)Delay Left 0–1000 ms, note Adjusts the delay time from the directsound until the delay sound isheard.-98–+98 % Adjusts the proportion of the delaysound that is fed back into the effect.Negative (-) settings will invertthe phase.HF Damp 200–8000 Hz, Adjusts the frequency above whichBYPASSsound fed back to the effect will becut. If you do not want to cut thehigh frequencies, set this parameterto BYPASS.Left Level 0–127 Volume of each delay soundRight LevelCenter LevelType: 3 (GM2 CHORUS)Pre-LPF 0–7 Cuts the high frequency range ofthe sound coming into the chorus.Higher values will cut more ofthe high frequencies.Level 0–127 Volume of the chorus soundFeedback 0–127 Adjusts the amount of the chorussound that is fed back into the effect.Delay 0–127 Adjusts the delay time from the directsound until the chorus sound isheard.Rate 0–127 Frequency of modulationDepth 0–127 Depth of modulationSend Level 0–127 Adjusts the amount of chorus soundTo Reverbthat will be sent to the reverb.note:(Sixty-fourth-note triplet), (Sixty-fourth note), (Thirty-second-note triplet),(Thirty-second note),(Sixteenth-note triplet),(Dotted thirty-second note),(Sixteenth note), (Eighth-note triplet), (Dotted sixteenth note),(Eighth note),(Quarter-note triplet),(Dotted eighth note),(Quarter note),(Half-note triplet),(Dotted quarter note),(Half note),(Whole-note triplet),(Double-note triplet),(Dotted half note),(Dotted whole note),(Whole note),(Double note)293