Owner's Manual - Roland

Effects List74: ENHANCER → DELAYfig.MFX-74L in EnhancerMixBalance DDelayFeedbackR in EnhancerMixBalance DL outBalance WBalance WR out76: FLANGER → DELAYfig.MFX-76Balance DL inFeedbackBalance WFlangerBalance WR inBalance DBalance DDelayFeedbackBalance DL outBalance WBalance WR outParameter Value DescriptionEnhancer Sens # 0–127 Sensitivity of the enhancerEnhancer Mix # 0–127 Level of the overtones generatedby the enhancerDelay Time 0–2600 ms, note Adjusts the delay time fromthe direct sound until the delaysound is heard.DelayFeedback #Delay HF Damp75: CHORUS → DELAYfig.MFX-75-98– +98 % Adjusts the proportion of thedelay sound that is fed backinto the effect. Negative (-)settings will invert the phase.200–8000 Hz,BYPASSAdjusts the frequency abovewhich sound fed back to theeffect will be cut. If you do notwant to cut the high frequencies,set this parameter to BY-PASS.Delay Balance # D100:0W–D0:100W Adjusts the volume balancebetween the sound that is sentthrough the delay (W) and thesound that is not sent throughthe delay (D).Level 0–127 Output LevelL inR inBalance DBalance WChorusBalance WBalance DBalance DDelayFeedbackBalance DL outBalance WBalance WR outParameter Value DescriptionFlanger PreDelay0.0–100.0 ms Adjusts the delay time fromwhen the direct sound beginsuntil the flanger sound isheard.Flanger Rate # 0.05–10.00 Hz, note Frequency of modulationFlanger Depth 0–127 Depth of modulationFlangerFeedback #FlangerBalance #-98– +98 % Adjusts the proportion of theflanger sound that is fed backinto the effect. Negative (-) settingswill invert the phase.D100:0W–D0:100W Volume balance between thedirect sound (D) and theflanger sound (W)Delay Time 0–2600 ms, note Adjusts the delay time fromthe direct sound until the delaysound is heard.DelayFeedback #Delay HFDampDelayBalance #-98– +98 % Adjusts the proportion of thedelay sound that is fed backinto the effect. Negative (-) settingswill invert the phase.200–8000 Hz,BYPASSD100:0W–D0:100WLevel 0–127 Output LevelAdjusts the frequency abovewhich sound fed back to the effectwill be cut. If you do notwant to cut the high frequencies,set this parameter to BY-PASS.Adjusts the volume balance betweenthe sound that is sentthrough the delay (W) and thesound that is not sent throughthe delay (D).Parameter Value DescriptionChorus PreDelay0.0–100.0 ms Adjusts the delay time from thedirect sound until the chorussound is heard.Chorus Rate # 0.05–10.00 Hz, note Frequency of modulationChorus Depth 0–127 Depth of modulationChorusBalance #D100:0W–D0:100WVolume balance between the directsound (D) and the chorussound (W)Delay Time 0–2600 ms, note Adjusts the delay time from thedirect sound until the delaysound is heard.DelayFeedback #Delay HFDampDelayBalance #-98– +98 % Adjusts the proportion of thedelay sound that is fed back intothe effect. Negative (-) settingswill invert the phase.200–8000 Hz,BYPASSD100:0W–D0:100WLevel 0–127 Output LevelAdjusts the frequency abovewhich sound fed back to the effectwill be cut. If you do notwant to cut the high frequencies,set this parameter to BY-PASS.Adjusts the volume balance betweenthe sound that is sentthrough the delay (W) and thesound that is not sent throughthe delay (D).291